Compare text

Find the difference between two text files

Real-time diff

Unified diff

Collapse lines

Highlight change

Syntax highlighting

Tools

Bad vs Good Boot 22.03.0

Created 2 years agoDiff never expires

F0: 102B 0000

F6: 0000 0000

V0: 0000 0000 [0001]

00: 0000 0000

BP: 0000 0041 [0000]

G0: 0190 0000

T0: 0000 036D [000F]

T0: 0000 036C [000F]

Jump to BL

UNIVPLL_CON0 = 0xFE000000!!!

mt_pll_init: Set pll frequency for 25M crystal

RAM_CONSOLE preloader last status: 0x0 0x0 0x0 0x0 0x0 0x0

[PMIC_WRAP]wrap_init pass,the return value=0.

[pmic_init] Preloader Start..................

[pmic_init] MT6380 CHIP Code, reg_val = 0, 1:E2 0:E3

[pmic_init] Done...................

Chip part number:7622B

MT7622 Version: 1.2.8, (iPA)

SSC OFF

mt_pll_post_init: mt_get_cpu_freq = 1350000Khz

mt_pll_post_init: mt_get_mem_freq = 1600000Khz

mt_pll_post_init: mt_get_bus_freq = 279980Khz

[PLFM] Init I2C: OK(0)

[BLDR] Build Time: 20210316-161525

==== Dump RGU Reg ========

RGU MODE: 14

RGU LENGTH: FFE0

RGU STA: 40000000

RGU INTERVAL: FFF

RGU SWSYSRST: 8000

==== Dump RGU Reg End ====

RGU: g_rgu_satus:2

mtk_wdt_mode_config mode value=10, tmp:22000010

PL RGU RST: ??

SW reset with bypass power key flag

Find bypass powerkey flag

WDT NONRST=0x20000000

WDT IRQ_EN=0x300002

WDT IRQ_EN=0x340003

RGU mtk_wdt_init:MTK_WDT_DEBUG_CTL(590200F3)

[EMI] MDL number = 2

[EMI] DRAMC calibration start

[DDR] Gating glitch patched (0<cnt<=6)

[EMI] DRAMC calibration end

[EMI]rank size auto detect

[EMI]start_addr[0x40000000]=0x12345678, test_addr[0x48000000]= 0xEDCBA987

[EMI]start_addr[0x40000000]=0xEDCBA987, test_addr[0x50000000]= 0xEDCBA987

[EMI]rank0 size: 0x10000000

[MEM] complex R/W mem test pass

RAM_CONSOLE wdt status (0x2)=0x2

mtk_snand_get_device_info

2-Recognize NAND: ID [C8 51 ], Device Name [GD5F1GQ5UEYIG], Page Size [2048]B Spare Size [128]B Total Size [128]MB

2-Recognize NAND: ID [C8 1 ], Device Name [F50L1G41LB], Page Size [2048]B Spare Size [64]B Total Size [128]MB

[BBT] BMT.v2 is found at 0x3FF

[PLFM] Init Boot Device: OK(0)

[PART] blksz: 2048B

[PART] [0x0000000000000000-0x000000000007FFFF] "PRELOADER" (256 blocks)

[PART] [0x0000000000080000-0x00000000000BFFFF] "tee1" (128 blocks)

[PART] [0x00000000000C0000-0x000000000013FFFF] "lk" (256 blocks)

Device APC domain init setup:

Domain Setup (0x0)

Device APC domain after setup:

Domain Setup (0x0)

[PART] Image with part header

[PART] name : U-Boot

[PART] addr : 41E00000h mode : -1

[PART] size : 356560

[PART] magic: 58881688h

[PART] load "lk" from 0x00000000000C0200 (dev) to 0x41E00000 (mem) [SUCCESS]

[PART] load speed: 16581KB/s, 356560 bytes, 21ms

load lk (ret=0)

[PART] Image with part header

[PART] name : atf

[PART] addr : FFFFFFFFh mode : -1

[PART] size : 57936

[PART] magic: 58881688h

[PART] load "tee1" from 0x0000000000080200 (dev) to 0x43000DC0 (mem) [SUCCESS]

[PART] load speed: 14144KB/s, 57936 bytes, 4ms

load tee1 (ret=0)

[BLDR] bldr load tee part ret=0x0, addr=0x43001000

[BLDR] boot part. not found

[BLDR] part_load_images ret=0x0

[BLDR] Others, jump to ATF

[BLDR] jump to 0x41E00000

[BLDR] <0x41E00000>=0xEA00000F

[BLDR] <0x41E00004>=0xE59FF014

U-Boot 2014.04-rc1 (Nov 12 2021 - 05:58:34)

auto detection g_total_rank_size = 0x F000000

DRAM: 240 MiB

Turn on power orange!

NAND: Recognize SNAND: ID [c8 51 ], Device Name [GD5F1GQ5UEYIG], Page Size [2048]B Spare Size [128]B Total Size [128]MB

NAND: Recognize SNAND: ID [c8 1 ], Device Name [F50L1G41LB], Page Size [2048]B Spare Size [64]B Total Size [128]MB

[mtk_snand] probe successfully!

Not found in UBOOT NAND flash list

[BBT] BMT.v2 is found at 0x3ff

128 MiB

In: serial

Out: serial

Err: serial

Net: mtk_eth

Uip activated

*** U-Boot SPI NAND ***

1. Load firmware 0 and bootup.

2. Load firmware 1 and bootup.

3. Load firmware selected by Xiaoqiang and bootup.

U-Boot console

trigger button release!

Press UP/DOWN to move or Press 1~3 to choose, ENTER to select

Erasing NAND...

[mtk_nand_erase_hw] mtk_nand_erase_hw @4249, ret:0x40. page:0x280

Erasing at 0x140000 -- 100% complete.

Writing to NAND... OK

Booting System 1

Booting System 0

NAND read: device 0 offset 0x2c0000, size 0x2000

8192 bytes read: OK

[do_read_image_blks] This is a FIT image,img_size = 0x39750c

[do_read_image_blks] img_blks = 0x72f

[do_read_image_blks] img_align_size = 0x397800

NAND read: device 0 offset 0x2c0000, size 0x397800

3766272 bytes read: OK

bootm flag=0, states=70f

## Loading kernel from FIT Image at 4007ff28 ...

Using 'config-1' configuration

Trying 'kernel-1' kernel subimage

Description: ARM64 OpenWrt Linux-5.10.138

Type: Kernel Image

Compression: lzma compressed

Data Start: 0x40080014

Data Size: 3734891 Bytes = 3.6 MiB

Architecture: AArch64

OS: Linux

Load Address: 0x44000000

Entry Point: 0x44000000

Hash algo: crc32

Hash value: 34277d02

Hash algo: sha1

Hash value: 59350071fab74c7ebc25527d129b8df03b928550

Verifying Hash Integrity ... crc32+ sha1+ OK

## Loading fdt from FIT Image at 4007ff28 ...

Using 'config-1' configuration

Trying 'fdt-1' fdt subimage

Description: ARM64 OpenWrt xiaomi_redmi-router-ax6s device tree blob

Type: Flat Device Tree

Compression: uncompressed

Data Start: 0x4040fec8

Data Size: 28699 Bytes = 28 KiB

Architecture: AArch64

Hash algo: crc32

Hash value: 5266c96c

Hash algo: sha1

Hash value: 971ba76339e05a4af50e447c1c18ffe13e6b9242

Verifying Hash Integrity ... crc32+ sha1+ OK

Booting using the fdt blob at 0x4040fec8

Uncompressing Kernel Image ... OK

Loading Device Tree to 4cf39000, end 4cf4301a ... OK

Starting kernel ...

[ATF][ 7.834669]save kernel info

[ATF][ 7.822817]save kernel info

[ATF][ 7.837606]Kernel_EL2

[ATF][ 7.825753]Kernel_EL2

[ATF][ 7.840276]Kernel is 64Bit

[ATF][ 7.828423]Kernel is 64Bit

[ATF][ 7.843364]pc=0x44000000, r0=0x4cf39000, r1=0x0

[ATF][ 7.831511]pc=0x44000000, r0=0x4cf39000, r1=0x0

INFO: BL3-1: Preparing for EL3 exit to normal world, Kernel

INFO: BL3-1: Next image address = 0x44000000

INFO: BL3-1: Next image spsr = 0x3c9

[ATF][ 7.861062]el3_exit

[ATF][ 7.849209]el3_exit

Booting Linux on physical CPU 0x0000000000 [0x410fd034]

Linux version 5.10.138 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19685-512e76967f) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Sat Sep 3 02:55:34 2022

Machine model: Xiaomi Redmi Router AX6S

Zone ranges:

DMA [mem 0x0000000040000000-0x000000004fffffff]

DMA32 empty

Normal empty

Movable zone start for each node

Early memory node ranges

node 0: [mem 0x0000000040000000-0x0000000042ffffff]

node 0: [mem 0x0000000043000000-0x000000004302ffff]

node 0: [mem 0x0000000043030000-0x000000004fffffff]

Initmem setup node 0 [mem 0x0000000040000000-0x000000004fffffff]

On node 0 totalpages: 65536

DMA zone: 1024 pages used for memmap

DMA zone: 0 pages reserved

DMA zone: 65536 pages, LIFO batch:15

psci: probing for conduit method from DT.

psci: PSCIv0.2 detected in firmware.

psci: Using standard PSCI v0.2 function IDs

psci: Trusted OS migration not required

percpu: Embedded 20 pages/cpu s43992 r8192 d29736 u81920

pcpu-alloc: s43992 r8192 d29736 u81920 alloc=20*4096

pcpu-alloc: [0] 0 [0] 1

Detected VIPT I-cache on CPU0

CPU features: detected: ARM erratum 845719

CPU features: kernel page table isolation disabled by kernel configuration

CPU features: detected: ARM erratum 843419

Built 1 zonelists, mobility grouping on. Total pages: 64512

Kernel command line: console=ttyS0,115200n1 loglevel=8 swiotlb=512 rootfstype=squashfs firmware=1 uart_en=1

Kernel command line: console=ttyS0,115200n1 loglevel=8 swiotlb=512 rootfstype=squashfs firmware=0 uart_en=1

Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, linear)

Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)

mem auto-init: stack:off, heap alloc:off, heap free:off

Memory: 232880K/262144K available (8254K kernel code, 894K rwdata, 1440K rodata, 448K init, 300K bss, 29264K reserved, 0K cma-reserved)

SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1

rcu: Hierarchical RCU implementation.

Tracing variant of Tasks RCU enabled.

rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.

NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0

GIC: GICv2 detected, but range too small and irqchip.gicv2_force_probe not set

arch_timer: cp15 timer(s) running at 12.50MHz (phys).

clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns

sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns

Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000)

pid_max: default: 32768 minimum: 301

Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear)

Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear)

rcu: Hierarchical SRCU implementation.

dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build

smp: Bringing up secondary CPUs ...

Detected VIPT I-cache on CPU1

CPU1: Booted secondary processor 0x0000000001 [0x410fd034]

smp: Brought up 1 node, 2 CPUs

SMP: Total of 2 processors activated.

CPU features: detected: 32-bit EL0 Support

CPU features: detected: CRC32 instructions

CPU: All CPU(s) started at EL2

alternatives: patching kernel code

clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns

futex hash table entries: 512 (order: 3, 32768 bytes, linear)

pinctrl core: initialized pinctrl subsystem

NET: Registered protocol family 16

DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations

DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations

DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations

thermal_sys: Registered thermal governor 'fair_share'

thermal_sys: Registered thermal governor 'bang_bang'

thermal_sys: Registered thermal governor 'step_wise'

thermal_sys: Registered thermal governor 'user_space'

ASID allocator initialised with 65536 entries

pstore: Registered ramoops as persistent store backend

ramoops: using 0x10000@0x42ff0000, ecc: 0

cryptd: max_cpu_qlen set to 1000

SCSI subsystem initialized

libata version 3.00 loaded.

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

clocksource: Switched to clocksource arch_sys_counter

NET: Registered protocol family 2

IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)

tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)

TCP established hash table entries: 2048 (order: 2, 16384 bytes, linear)

TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear)

TCP: Hash tables configured (established 2048 bind 2048)

UDP hash table entries: 256 (order: 1, 8192 bytes, linear)

UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)

NET: Registered protocol family 1

PCI: CLS 0 bytes, default 64

workingset: timestamp_bits=46 max_order=16 bucket_order=0

squashfs: version 4.0 (2009/01/31) Phillip Lougher

Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)

mt-pmic-pwrap 10001000.pwrap: unexpected interrupt int=0x1

Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled

printk: console [ttyS0] disabled

11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 21, base_baud = 1562500) is a ST16650V2

printk: console [ttyS0] enabled

mtk_rng 1020f000.rng: registered RNG driver

random: crng init done

cacheinfo: Unable to detect cache hierarchy for CPU 0

loop: module loaded

Loading iSCSI transport class v2.0-870.

mtk-snand 1100d000.snfi: chip is GD5F1GQ5xExxG, size 128MB, page size 2048, oob size 128

mtk-snand 1100d000.snfi: chip is F50L1G41LB, size 128MB, page size 2048, oob size 64

[BBT] BMT.v2 is found at 0x3fe

[BBT] BMT.v2 is found at 0x3ff

10 fixed-partitions partitions found on MTD device 1100d000.snfi

Creating 10 MTD partitions on "1100d000.snfi":

0x000000000000-0x000000080000 : "Preloader"

0x000000080000-0x0000000c0000 : "ATF"

0x0000000c0000-0x000000140000 : "u-boot"

0x000000140000-0x000000180000 : "u-boot-env"

0x000000180000-0x0000001c0000 : "bdata"

0x0000001c0000-0x000000240000 : "factory"

0x000000240000-0x000000280000 : "crash"

0x000000280000-0x0000002c0000 : "crash_log"

0x0000002c0000-0x0000006c0000 : "kernel"

2 fit-fw partitions found on MTD device kernel

no rootfs found after FIT image in "kernel"

Creating 2 MTD partitions on "kernel":

0x000000000000-0x0000003a0000 : "kernel"

0x0000003e0000-0x000000400000 : "rootfs"

mtd: device 10 (rootfs) set to be root filesystem

mtdsplit: no squashfs found in "rootfs"

0x0000006c0000-0x0000075c0000 : "ubi"

mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xffffffc011c80000, irq 30

i2c /dev entries driver

mtk-wdt 10212000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)

NET: Registered protocol family 10

Segment Routing with IPv6

NET: Registered protocol family 17

bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.

8021q: 802.1Q VLAN Support v1.8

pstore: Using crash dump compression: deflate

mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges:

mtk-pcie 1a143000.pcie: Parsing ranges property...

mtk-pcie 1a143000.pcie: MEM 0x0020000000..0x0027ffffff -> 0x0020000000

mtk-pcie 1a143000.pcie: PCI host bridge to bus 0000:00

pci_bus 0000:00: root bus resource [bus 00-ff]

pci_bus 0000:00: root bus resource [mem 0x20000000-0x27ffffff]

pci_bus 0000:00: scanning bus

pci 0000:00:00.0: [14c3:3258] type 01 class 0x060400

pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x1ffffffff 64bit pref]

pci_bus 0000:00: fixups for bus

pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0

pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring

pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1

pci_bus 0000:01: scanning bus

pci 0000:01:00.0: [14c3:7915] type 00 class 0x000280

pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]

pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]

pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]

pci 0000:01:00.0: supports D1 D2

pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold

pci 0000:01:00.0: PME# disabled

pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)

pci_bus 0000:01: fixups for bus

pci_bus 0000:01: bus scan returning with max=01

pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01

pci_bus 0000:00: bus scan returning with max=01

pci 0000:00:00.0: BAR 0: no space for [mem size 0x200000000 64bit pref]

pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x200000000 64bit pref]

pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]

pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit pref]

pci 0000:01:00.0: BAR 2: assigned [mem 0x20100000-0x20103fff 64bit pref]

pci 0000:01:00.0: BAR 4: assigned [mem 0x20104000-0x20104fff 64bit pref]

pci 0000:00:00.0: PCI bridge to [bus 01]

pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff]

pcieport 0000:00:00.0: of_irq_parse_pci: failed with rc=-22

pcieport 0000:00:00.0: assign IRQ: got 0

pcieport 0000:00:00.0: enabling device (0000 -> 0002)

pcieport 0000:00:00.0: enabling bus mastering

mtk_hsdma 1b007000.dma-controller: Using 3 as missing dma-requests property

mtk_hsdma 1b007000.dma-controller: MediaTek HSDMA driver registered

mt7530 mdio-bus:00 wan (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=138)

mt7530 mdio-bus:00 lan1 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=139)

mt7530 mdio-bus:00 lan2 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=140)

mt7530 mdio-bus:00 lan3 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=141)

mt7530 mdio-bus:00: configuring for fixed/2500base-x link mode

DSA: tree 0 setup

mt7530 mdio-bus:00: Link is Up - 2.5Gbps/Full - flow control rx/tx

UBI: auto-attach mtd11

UBI: auto-attach mtd9

ubi0: attaching mtd11

ubi0: attaching mtd9

UBI: EOF marker found, PEBs from 43 will be erased

ubi0: scanning is finished

ubi0: volume 1 ("rootfs_data") re-sized from 9 to 824 LEBs

ubi0: attached mtd9 (name "ubi", size 111 MiB)

ubi0: attached mtd11 (name "ubi", size 111 MiB)

ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes

ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048

ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096

ubi0: good PEBs: 888, bad PEBs: 0, corrupted PEBs: 0

ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128

ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1662173734

ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1662173734

ubi0: available PEBs: 0, total reserved PEBs: 888, PEBs reserved for bad PEB handling: 19

ubi0: background thread "ubi_bgt0d" started, PID 773

ubi0: background thread "ubi_bgt0d" started, PID 763

block ubiblock0_0: created from ubi0:0(rootfs)

List of all partitions:

ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem

1f00 512 mtdblock0

VFS: Mounted root (squashfs filesystem) readonly on device 259:0.

(driver?)

Freeing unused kernel memory: 448K

1f04 256 mtdblock1

Run /sbin/init as init process

(driver?)

with arguments:

1f08 512 mtdblock2

/sbin/init

(driver?)

with environment:

1f0c 256 mtdblock3

HOME=/

(driver?)

TERM=linux

1f10 256 mtdblock4

firmware=0

(driver?)

uart_en=1

1f14 512 mtdblock5

init: Console is alive

(driver?)

init: - watchdog -

1f18 256 mtdblock6

kmodloader: loading kernel modules from /etc/modules-boot.d/*

(driver?)

kmodloader: done loading kernel modules from /etc/modules-boot.d/*

1f1c 256 mtdblock7

init: - preinit -

(driver?)

mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode

1f20 4096 mtdblock8

mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx

(driver?)

IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

1f24 3712 mtdblock9

mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode

(driver?)

8021q: adding VLAN 0 to HW filter on device lan1

1f28 128 mtdblock10

Press the [f] key and hit [enter] to enter failsafe mode

(driver?)

Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level

1f2c 113664 mtdblock11

mt7530 mdio-bus:00 lan1: Link is Up - 1Gbps/Full - flow control rx/tx

(driver?)

IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready

103:00000 5084 ubiblock0_0

UBIFS (ubi0:1): Mounting in unauthenticated mode

(driver?)

UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 842

No filesystem could mount root, tried:

UBIFS (ubi0:1): recovery needed

squashfs

UBIFS (ubi0:1): recovery completed

[ 2.054652]

UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"

Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,40)

UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes

SMP: stopping secondary CPUs

UBIFS (ubi0:1): FS size: 103231488 bytes (98 MiB, 813 LEBs), journal size 5206016 bytes (4 MiB, 41 LEBs)

Kernel Offset: disabled

UBIFS (ubi0:1): reserved for root: 4875878 bytes (4761 KiB)

CPU features: 0x0000002,04002004

UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 1D56BA8C-4CE9-4A65-88F2-ABC1E6F24129, small LPT model

Memory Limit: none

mount_root: switching to ubifs overlay

Rebooting in 1 seconds..

overlayfs: "xino" feature enabled using 2 upper inode bits.

urandom-seed: Seeding with /etc/urandom.seed

mt7530 mdio-bus:00 lan1: Link is Down

procd: - early -

procd: - watchdog -

procd: - ubus -

procd: - init -

Please press Enter to activate this console.

urngd: v1.0.2 started.

kmodloader: loading kernel modules from /etc/modules.d/*

Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064

Backport generated by backports.git v5.15.58-1-0-g42a95ce7

ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'

mt7915e 0000:01:00.0: assign IRQ: got 142

pci 0000:00:00.0: enabling bus mastering

mt7915e 0000:01:00.0: enabling device (0000 -> 0002)

mt7915e 0000:01:00.0: enabling bus mastering

mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a

[ 8.541008]

mt7622-wmac 18000000.wmac: N9 Firmware Version: _reserved_, Build Time: 20220630094834

mt7915e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20211222184017a

[ 8.731471]

mt7915e 0000:01:00.0: WM Firmware Version: ____000000, Build Time: 20211222184052

mt7915e 0000:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20211222184111

PPP generic driver version 2.4.2

NET: Registered protocol family 24

kmodloader: done loading kernel modules from /etc/modules.d/*

[ 10.675791] mtk_soc_eth 1b100000.ethernet eth0: Link is Down

[ 10.684772] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode

[ 10.693258] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx

[ 10.701988] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

[ 10.712980] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode

[ 10.722867] 8021q: adding VLAN 0 to HW filter on device lan1

[ 10.731620] br-lan: port 1(lan1) entered blocking state

[ 10.736853] br-lan: port 1(lan1) entered disabled state

[ 10.744517] device lan1 entered promiscuous mode

[ 10.749234] device eth0 entered promiscuous mode

[ 10.760191] mt7530 mdio-bus:00 lan2: configuring for phy/gmii link mode

[ 10.776804] 8021q: adding VLAN 0 to HW filter on device lan2

[ 10.787687] br-lan: port 2(lan2) entered blocking state

[ 10.792920] br-lan: port 2(lan2) entered disabled state

[ 10.802265] device lan2 entered promiscuous mode

[ 10.814022] mt7530 mdio-bus:00 lan3: configuring for phy/gmii link mode

[ 10.822525] 8021q: adding VLAN 0 to HW filter on device lan3

[ 10.831245] br-lan: port 3(lan3) entered blocking state

[ 10.836476] br-lan: port 3(lan3) entered disabled state

[ 10.844302] device lan3 entered promiscuous mode

[ 10.854103] mt7530 mdio-bus:00 wan: configuring for phy/gmii link mode

[ 10.861212] 8021q: adding VLAN 0 to HW filter on device wan

[ 10.869162] br-lan: port 4(wan) entered blocking state

[ 10.874308] br-lan: port 4(wan) entered disabled state

[ 10.880936] device wan entered promiscuous mode

[ 12.144964] br-lan: port 5(wlan0-1) entered blocking state

[ 12.150560] br-lan: port 5(wlan0-1) entered disabled state

[ 12.156274] device wlan0-1 entered promiscuous mode

[ 12.161291] br-lan: port 5(wlan0-1) entered blocking state

[ 12.166776] br-lan: port 5(wlan0-1) entered forwarding state

[ 12.172687] br-lan: port 5(wlan0-1) entered disabled state

[ 12.336907] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready

[ 12.343558] br-lan: port 5(wlan0-1) entered blocking state

[ 12.349050] br-lan: port 5(wlan0-1) entered forwarding state

[ 12.354882] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready

[ 13.772289] mt7530 mdio-bus:00 lan1: Link is Up - 1Gbps/Full - flow control rx/tx

[ 14.778834] br-lan: port 1(lan1) entered blocking state

[ 14.784072] br-lan: port 1(lan1) entered forwarding state

[ 14.790108] br-lan: port 6(wlan1-1) entered blocking state

[ 14.795613] br-lan: port 6(wlan1-1) entered disabled state

[ 14.801344] device wlan1-1 entered promiscuous mode

[ 15.097332] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-1: link becomes ready

[ 15.103952] br-lan: port 6(wlan1-1) entered blocking state

[ 15.109449] br-lan: port 6(wlan1-1) entered forwarding state

[ 15.230272] br-lan: port 7(wlan0) entered blocking state

[ 15.235588] br-lan: port 7(wlan0) entered disabled state

[ 15.241176] device wlan0 entered promiscuous mode

[ 15.847034] br-lan: port 5(wlan0-1) entered disabled state

[ 16.506313] br-lan: port 8(wlan1) entered blocking state

[ 16.511668] br-lan: port 8(wlan1) entered disabled state

[ 16.517186] device wlan1 entered promiscuous mode

[ 16.678541] br-lan: port 5(wlan0-1) entered blocking state

[ 16.684041] br-lan: port 5(wlan0-1) entered forwarding state

[ 16.745875] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready

[ 16.752369] br-lan: port 7(wlan0) entered blocking state

[ 16.757744] br-lan: port 7(wlan0) entered forwarding state

[ 16.857225] br-lan: port 6(wlan1-1) entered disabled state

[ 17.768776] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:8f, vlan:0)

[ 17.785583] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:8f, vlan:0)

[ 17.928916] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:8f, vlan:0)

[ 18.028470] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:8f, vlan:0)

[ 18.781103] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:8f, vlan:0)

[ 21.138599] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready

[ 21.145146] br-lan: port 8(wlan1) entered blocking state

[ 21.150521] br-lan: port 8(wlan1) entered forwarding state

[ 21.157484] br-lan: port 6(wlan1-1) entered blocking state

[ 21.162978] br-lan: port 6(wlan1-1) entered forwarding state

[ 21.768587] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)

[ 21.779387] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)

[ 21.789829] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)

[ 21.790404] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)

[ 21.800054] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)

[ 22.780977] net_ratelimit: 243 callbacks suppressed

[ 22.780984] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)

[ 22.783012] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)

[ 22.785970] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)

[ 22.796115] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)

[ 22.806152] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)

[ 22.816321] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)

[ 22.827130] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)

[ 22.836646] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)

[ 22.846665] br-lan: received packet on wlan1 with own address as sour

Saved diffs

Original text

Open file

F0: 102B 0000
F6: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 0000 0041 [0000]
G0: 0190 0000
T0: 0000 036D [000F]
Jump to BL

UNIVPLL_CON0 = 0xFE000000!!!
mt_pll_init: Set pll frequency for 25M crystal
RAM_CONSOLE preloader last status: 0x0 0x0 0x0 0x0 0x0 0x0
[PMIC_WRAP]wrap_init pass,the return value=0.
[pmic_init] Preloader Start..................
[pmic_init] MT6380 CHIP Code, reg_val = 0, 1:E2  0:E3
[pmic_init] Done...................
Chip part number:7622B
MT7622 Version: 1.2.8, (iPA)
SSC OFF
mt_pll_post_init: mt_get_cpu_freq = 1350000Khz
mt_pll_post_init: mt_get_mem_freq = 1600000Khz
mt_pll_post_init: mt_get_bus_freq = 279980Khz
[PLFM] Init I2C: OK(0)

[BLDR] Build Time: 20210316-161525
==== Dump RGU Reg ========
RGU MODE:     14
RGU LENGTH:   FFE0
RGU STA:      40000000
RGU INTERVAL: FFF
RGU SWSYSRST: 8000
==== Dump RGU Reg End ====
RGU: g_rgu_satus:2
 mtk_wdt_mode_config  mode value=10, tmp:22000010
PL RGU RST: ??
SW reset with bypass power key flag
Find bypass powerkey flag
WDT NONRST=0x20000000
WDT IRQ_EN=0x300002
RGU mtk_wdt_init:MTK_WDT_DEBUG_CTL(590200F3)
[EMI] MDL number = 2
[EMI] DRAMC calibration start

[DDR] Gating glitch patched (0<cnt<=6)
[EMI] DRAMC calibration end

[EMI]rank size auto detect
[EMI]start_addr[0x40000000]=0x12345678, test_addr[0x48000000]= 0xEDCBA987
[EMI]start_addr[0x40000000]=0xEDCBA987, test_addr[0x50000000]= 0xEDCBA987
[EMI]rank0 size: 0x10000000
[MEM] complex R/W mem test pass
RAM_CONSOLE wdt status (0x2)=0x2
mtk_snand_get_device_info
2-Recognize NAND: ID [C8 51 ], Device Name [GD5F1GQ5UEYIG], Page Size [2048]B Spare Size [128]B Total Size [128]MB
[BBT] BMT.v2 is found at 0x3FF
[PLFM] Init Boot Device: OK(0)

[PART] blksz: 2048B
[PART] [0x0000000000000000-0x000000000007FFFF] "PRELOADER" (256 blocks)
[PART] [0x0000000000080000-0x00000000000BFFFF] "tee1" (128 blocks)
[PART] [0x00000000000C0000-0x000000000013FFFF] "lk" (256 blocks)

Device APC domain init setup:

Domain Setup (0x0)
Domain Setup (0x0)
Device APC domain after setup:
Domain Setup (0x0)
Domain Setup (0x0)
[PART] Image with part header
[PART] name : U-Boot
[PART] addr : 41E00000h mode : -1
[PART] size : 356560
[PART] magic: 58881688h

[PART] load "lk" from 0x00000000000C0200 (dev) to 0x41E00000 (mem) [SUCCESS]
[PART] load speed: 16581KB/s, 356560 bytes, 21ms
load lk (ret=0)
[PART] Image with part header
[PART] name : atf
[PART] addr : FFFFFFFFh mode : -1
[PART] size : 57936
[PART] magic: 58881688h

[PART] load "tee1" from 0x0000000000080200 (dev) to 0x43000DC0 (mem) [SUCCESS]
[PART] load speed: 14144KB/s, 57936 bytes, 4ms
load tee1 (ret=0)
[BLDR] bldr load tee part ret=0x0, addr=0x43001000
[BLDR] boot part. not found
[BLDR] part_load_images ret=0x0
[BLDR] Others, jump to ATF

[BLDR] jump to 0x41E00000
[BLDR] <0x41E00000>=0xEA00000F
[BLDR] <0x41E00004>=0xE59FF014


U-Boot 2014.04-rc1 (Nov 12 2021 - 05:58:34)

auto detection g_total_rank_size = 0x F000000
DRAM:  240 MiB
Turn on power orange!
NAND:  Recognize SNAND: ID [c8 51 ], Device Name [GD5F1GQ5UEYIG], Page Size [2048]B Spare Size [128]B Total Size [128]MB
[mtk_snand] probe successfully!
Not found in UBOOT NAND flash list
[BBT] BMT.v2 is found at 0x3ff
128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   mtk_eth
Uip activated

  *** U-Boot SPI NAND ***

     1. Load firmware 0 and bootup.
     2. Load firmware 1 and bootup.
     3. Load firmware selected by Xiaoqiang and bootup.
     U-Boot console

 trigger button release!
  Press UP/DOWN to move or Press 1~3 to choose, ENTER to select
Erasing NAND...
[mtk_nand_erase_hw] mtk_nand_erase_hw @4249, ret:0x40. page:0x280
Erasing at 0x140000 -- 100% complete.
Writing to NAND... OK
Booting System 1

NAND read: device 0 offset 0x2c0000, size 0x2000
 8192 bytes read: OK
[do_read_image_blks] This is a FIT image,img_size = 0x39750c
[do_read_image_blks] img_blks = 0x72f
[do_read_image_blks] img_align_size = 0x397800

NAND read: device 0 offset 0x2c0000, size 0x397800
 3766272 bytes read: OK
bootm flag=0, states=70f
## Loading kernel from FIT Image at 4007ff28 ...
   Using 'config-1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  ARM64 OpenWrt Linux-5.10.138
     Type:         Kernel Image
     Compression:  lzma compressed
     Data Start:   0x40080014
     Data Size:    3734891 Bytes = 3.6 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x44000000
     Entry Point:  0x44000000
     Hash algo:    crc32
     Hash value:   34277d02
     Hash algo:    sha1
     Hash value:   59350071fab74c7ebc25527d129b8df03b928550
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 4007ff28 ...
   Using 'config-1' configuration
   Trying 'fdt-1' fdt subimage
     Description:  ARM64 OpenWrt xiaomi_redmi-router-ax6s device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x4040fec8
     Data Size:    28699 Bytes = 28 KiB
     Architecture: AArch64
     Hash algo:    crc32
     Hash value:   5266c96c
     Hash algo:    sha1
     Hash value:   971ba76339e05a4af50e447c1c18ffe13e6b9242
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x4040fec8
   Uncompressing Kernel Image ... OK
   Loading Device Tree to 4cf39000, end 4cf4301a ... OK

Starting kernel ...

[ATF][     7.834669]save kernel info
[ATF][     7.837606]Kernel_EL2
[ATF][     7.840276]Kernel is 64Bit
[ATF][     7.843364]pc=0x44000000, r0=0x4cf39000, r1=0x0
INFO:    BL3-1: Preparing for EL3 exit to normal world, Kernel
INFO:    BL3-1: Next image address = 0x44000000
INFO:    BL3-1: Next image spsr = 0x3c9
[ATF][     7.861062]el3_exit

Booting Linux on physical CPU 0x0000000000 [0x410fd034]
Linux version 5.10.138 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19685-512e76967f) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Sat Sep 3 02:55:34 2022
Machine model: Xiaomi Redmi Router AX6S
Zone ranges:
  DMA      [mem 0x0000000040000000-0x000000004fffffff]
  DMA32    empty
  Normal   empty
Movable zone start for each node
Early memory node ranges
  node   0: [mem 0x0000000040000000-0x0000000042ffffff]
  node   0: [mem 0x0000000043000000-0x000000004302ffff]
  node   0: [mem 0x0000000043030000-0x000000004fffffff]
Initmem setup node 0 [mem 0x0000000040000000-0x000000004fffffff]
On node 0 totalpages: 65536
  DMA zone: 1024 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 65536 pages, LIFO batch:15
psci: probing for conduit method from DT.
psci: PSCIv0.2 detected in firmware.
psci: Using standard PSCI v0.2 function IDs
psci: Trusted OS migration not required
percpu: Embedded 20 pages/cpu s43992 r8192 d29736 u81920
pcpu-alloc: s43992 r8192 d29736 u81920 alloc=20*4096
pcpu-alloc: [0] 0 [0] 1
Detected VIPT I-cache on CPU0
CPU features: detected: ARM erratum 845719
CPU features: kernel page table isolation disabled by kernel configuration
CPU features: detected: ARM erratum 843419
Built 1 zonelists, mobility grouping on.  Total pages: 64512
Kernel command line: console=ttyS0,115200n1 loglevel=8 swiotlb=512 rootfstype=squashfs firmware=1 uart_en=1
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
mem auto-init: stack:off, heap alloc:off, heap free:off
Memory: 232880K/262144K available (8254K kernel code, 894K rwdata, 1440K rodata, 448K init, 300K bss, 29264K reserved, 0K cma-reserved)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
rcu: Hierarchical RCU implementation.
 Tracing variant of Tasks RCU enabled.
rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
GIC: GICv2 detected, but range too small and irqchip.gicv2_force_probe not set
arch_timer: cp15 timer(s) running at 12.50MHz (phys).
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns
Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
rcu: Hierarchical SRCU implementation.
dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
smp: Bringing up secondary CPUs ...
Detected VIPT I-cache on CPU1
CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
smp: Brought up 1 node, 2 CPUs
SMP: Total of 2 processors activated.
CPU features: detected: 32-bit EL0 Support
CPU features: detected: CRC32 instructions
CPU: All CPU(s) started at EL2
alternatives: patching kernel code
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 512 (order: 3, 32768 bytes, linear)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
thermal_sys: Registered thermal governor 'fair_share'
thermal_sys: Registered thermal governor 'bang_bang'
thermal_sys: Registered thermal governor 'step_wise'
thermal_sys: Registered thermal governor 'user_space'
ASID allocator initialised with 65536 entries
pstore: Registered ramoops as persistent store backend
ramoops: using 0x10000@0x42ff0000, ecc: 0
cryptd: max_cpu_qlen set to 1000
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
clocksource: Switched to clocksource arch_sys_counter
NET: Registered protocol family 2
IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
TCP established hash table entries: 2048 (order: 2, 16384 bytes, linear)
TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
NET: Registered protocol family 1
PCI: CLS 0 bytes, default 64
workingset: timestamp_bits=46 max_order=16 bucket_order=0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
mt-pmic-pwrap 10001000.pwrap: unexpected interrupt int=0x1
Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
printk: console [ttyS0] disabled
11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 21, base_baud = 1562500) is a ST16650V2
printk: console [ttyS0] enabled
mtk_rng 1020f000.rng: registered RNG driver
random: crng init done
cacheinfo: Unable to detect cache hierarchy for CPU 0
loop: module loaded
Loading iSCSI transport class v2.0-870.
mtk-snand 1100d000.snfi: chip is GD5F1GQ5xExxG, size 128MB, page size 2048, oob size 128
[BBT] BMT.v2 is found at 0x3fe
10 fixed-partitions partitions found on MTD device 1100d000.snfi
Creating 10 MTD partitions on "1100d000.snfi":
0x000000000000-0x000000080000 : "Preloader"
0x000000080000-0x0000000c0000 : "ATF"
0x0000000c0000-0x000000140000 : "u-boot"
0x000000140000-0x000000180000 : "u-boot-env"
0x000000180000-0x0000001c0000 : "bdata"
0x0000001c0000-0x000000240000 : "factory"
0x000000240000-0x000000280000 : "crash"
0x000000280000-0x0000002c0000 : "crash_log"
0x0000002c0000-0x0000006c0000 : "kernel"
2 fit-fw partitions found on MTD device kernel
Creating 2 MTD partitions on "kernel":
0x000000000000-0x0000003a0000 : "kernel"
0x0000003e0000-0x000000400000 : "rootfs"
mtd: device 10 (rootfs) set to be root filesystem
mtdsplit: no squashfs found in "rootfs"
0x0000006c0000-0x0000075c0000 : "ubi"
mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xffffffc011c80000, irq 30
i2c /dev entries driver
mtk-wdt 10212000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
NET: Registered protocol family 10
Segment Routing with IPv6
NET: Registered protocol family 17
bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
8021q: 802.1Q VLAN Support v1.8
pstore: Using crash dump compression: deflate
mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges:
mtk-pcie 1a143000.pcie: Parsing ranges property...
mtk-pcie 1a143000.pcie:      MEM 0x0020000000..0x0027ffffff -> 0x0020000000
mtk-pcie 1a143000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [mem 0x20000000-0x27ffffff]
pci_bus 0000:00: scanning bus
pci 0000:00:00.0: [14c3:3258] type 01 class 0x060400
pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x1ffffffff 64bit pref]
pci_bus 0000:00: fixups for bus
pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0
pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1
pci_bus 0000:01: scanning bus
pci 0000:01:00.0: [14c3:7915] type 00 class 0x000280
pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
pci 0000:01:00.0: supports D1 D2
pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
pci_bus 0000:01: fixups for bus
pci_bus 0000:01: bus scan returning with max=01
pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
pci_bus 0000:00: bus scan returning with max=01
pci 0000:00:00.0: BAR 0: no space for [mem size 0x200000000 64bit pref]
pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x200000000 64bit pref]
pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit pref]
pci 0000:01:00.0: BAR 2: assigned [mem 0x20100000-0x20103fff 64bit pref]
pci 0000:01:00.0: BAR 4: assigned [mem 0x20104000-0x20104fff 64bit pref]
pci 0000:00:00.0: PCI bridge to [bus 01]
pci 0000:00:00.0:   bridge window [mem 0x20000000-0x201fffff]
pcieport 0000:00:00.0: of_irq_parse_pci: failed with rc=-22
pcieport 0000:00:00.0: assign IRQ: got 0
pcieport 0000:00:00.0: enabling device (0000 -> 0002)
pcieport 0000:00:00.0: enabling bus mastering
mtk_hsdma 1b007000.dma-controller: Using 3 as missing dma-requests property
mtk_hsdma 1b007000.dma-controller: MediaTek HSDMA driver registered
mt7530 mdio-bus:00 wan (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=138)
mt7530 mdio-bus:00 lan1 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=139)
mt7530 mdio-bus:00 lan2 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=140)
mt7530 mdio-bus:00 lan3 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=141)
mt7530 mdio-bus:00: configuring for fixed/2500base-x link mode
DSA: tree 0 setup
mt7530 mdio-bus:00: Link is Up - 2.5Gbps/Full - flow control rx/tx
UBI: auto-attach mtd11
ubi0: attaching mtd11
UBI: EOF marker found, PEBs from 43 will be erased
ubi0: scanning is finished
ubi0: volume 1 ("rootfs_data") re-sized from 9 to 824 LEBs
ubi0: attached mtd11 (name "ubi", size 111 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 888, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1662173734
ubi0: available PEBs: 0, total reserved PEBs: 888, PEBs reserved for bad PEB handling: 19
ubi0: background thread "ubi_bgt0d" started, PID 773
block ubiblock0_0: created from ubi0:0(rootfs)
List of all partitions:
1f00             512 mtdblock0
 (driver?)
1f04             256 mtdblock1
 (driver?)
1f08             512 mtdblock2
 (driver?)
1f0c             256 mtdblock3
 (driver?)
1f10             256 mtdblock4
 (driver?)
1f14             512 mtdblock5
 (driver?)
1f18             256 mtdblock6
 (driver?)
1f1c             256 mtdblock7
 (driver?)
1f20            4096 mtdblock8
 (driver?)
1f24            3712 mtdblock9
 (driver?)
1f28             128 mtdblock10
 (driver?)
1f2c          113664 mtdblock11
 (driver?)
103:00000       5084 ubiblock0_0
 (driver?)
No filesystem could mount root, tried:
 squashfs
[    2.054652]
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,40)
SMP: stopping secondary CPUs
Kernel Offset: disabled
CPU features: 0x0000002,04002004
Memory Limit: none
Rebooting in 1 seconds..

Changed text

Open file

F0: 102B 0000
F6: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 0000 0041 [0000]
G0: 0190 0000
T0: 0000 036C [000F]
Jump to BL

UNIVPLL_CON0 = 0xFE000000!!!
mt_pll_init: Set pll frequency for 25M crystal
RAM_CONSOLE preloader last status: 0x0 0x0 0x0 0x0 0x0 0x0
[PMIC_WRAP]wrap_init pass,the return value=0.
[pmic_init] Preloader Start..................
[pmic_init] MT6380 CHIP Code, reg_val = 0, 1:E2  0:E3
[pmic_init] Done...................
Chip part number:7622B
MT7622 Version: 1.2.8, (iPA)
SSC OFF
mt_pll_post_init: mt_get_cpu_freq = 1350000Khz
mt_pll_post_init: mt_get_mem_freq = 1600000Khz
mt_pll_post_init: mt_get_bus_freq = 279980Khz
[PLFM] Init I2C: OK(0)

[BLDR] Build Time: 20210316-161525
==== Dump RGU Reg ========
RGU MODE:     14
RGU LENGTH:   FFE0
RGU STA:      40000000
RGU INTERVAL: FFF
RGU SWSYSRST: 8000
==== Dump RGU Reg End ====
RGU: g_rgu_satus:2
 mtk_wdt_mode_config  mode value=10, tmp:22000010
PL RGU RST: ??
SW reset with bypass power key flag
Find bypass powerkey flag
WDT NONRST=0x20000000
WDT IRQ_EN=0x340003
RGU mtk_wdt_init:MTK_WDT_DEBUG_CTL(590200F3)
[EMI] MDL number = 2
[EMI] DRAMC calibration start

[EMI] DRAMC calibration end

[EMI]rank size auto detect
[EMI]start_addr[0x40000000]=0x12345678, test_addr[0x48000000]= 0xEDCBA987
[EMI]start_addr[0x40000000]=0xEDCBA987, test_addr[0x50000000]= 0xEDCBA987
[EMI]rank0 size: 0x10000000
[MEM] complex R/W mem test pass
RAM_CONSOLE wdt status (0x2)=0x2
mtk_snand_get_device_info
2-Recognize NAND: ID [C8 1 ], Device Name [F50L1G41LB], Page Size [2048]B Spare Size [64]B Total Size [128]MB
[BBT] BMT.v2 is found at 0x3FF
[PLFM] Init Boot Device: OK(0)

[PART] blksz: 2048B
[PART] [0x0000000000000000-0x000000000007FFFF] "PRELOADER" (256 blocks)
[PART] [0x0000000000080000-0x00000000000BFFFF] "tee1" (128 blocks)
[PART] [0x00000000000C0000-0x000000000013FFFF] "lk" (256 blocks)

Device APC domain init setup:

Domain Setup (0x0)
Domain Setup (0x0)
Device APC domain after setup:
Domain Setup (0x0)
Domain Setup (0x0)
[PART] Image with part header
[PART] name : U-Boot
[PART] addr : 41E00000h mode : -1
[PART] size : 356560
[PART] magic: 58881688h

[PART] load "lk" from 0x00000000000C0200 (dev) to 0x41E00000 (mem) [SUCCESS]
[PART] load speed: 16581KB/s, 356560 bytes, 21ms
load lk (ret=0)
[PART] Image with part header
[PART] name : atf
[PART] addr : FFFFFFFFh mode : -1
[PART] size : 57936
[PART] magic: 58881688h

[PART] load "tee1" from 0x0000000000080200 (dev) to 0x43000DC0 (mem) [SUCCESS]
[PART] load speed: 14144KB/s, 57936 bytes, 4ms
load tee1 (ret=0)
[BLDR] bldr load tee part ret=0x0, addr=0x43001000
[BLDR] boot part. not found
[BLDR] part_load_images ret=0x0
[BLDR] Others, jump to ATF

[BLDR] jump to 0x41E00000
[BLDR] <0x41E00000>=0xEA00000F
[BLDR] <0x41E00004>=0xE59FF014


U-Boot 2014.04-rc1 (Nov 12 2021 - 05:58:34)

auto detection g_total_rank_size = 0x F000000
DRAM:  240 MiB
Turn on power orange!
NAND:  Recognize SNAND: ID [c8 1 ], Device Name [F50L1G41LB], Page Size [2048]B Spare Size [64]B Total Size [128]MB
[mtk_snand] probe successfully!
[BBT] BMT.v2 is found at 0x3ff
128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   mtk_eth
Uip activated

  *** U-Boot SPI NAND ***

     1. Load firmware 0 and bootup.
     2. Load firmware 1 and bootup.
     3. Load firmware selected by Xiaoqiang and bootup.
     U-Boot console

 trigger button release!
  Press UP/DOWN to move or Press 1~3 to choose, ENTER to select
Erasing NAND...
[mtk_nand_erase_hw] mtk_nand_erase_hw @4249, ret:0x40. page:0x280
Erasing at 0x140000 -- 100% complete.
Writing to NAND... OK
Booting System 0

NAND read: device 0 offset 0x2c0000, size 0x2000
 8192 bytes read: OK
[do_read_image_blks] This is a FIT image,img_size = 0x39750c
[do_read_image_blks] img_blks = 0x72f
[do_read_image_blks] img_align_size = 0x397800

NAND read: device 0 offset 0x2c0000, size 0x397800
 3766272 bytes read: OK
bootm flag=0, states=70f
## Loading kernel from FIT Image at 4007ff28 ...
   Using 'config-1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  ARM64 OpenWrt Linux-5.10.138
     Type:         Kernel Image
     Compression:  lzma compressed
     Data Start:   0x40080014
     Data Size:    3734891 Bytes = 3.6 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x44000000
     Entry Point:  0x44000000
     Hash algo:    crc32
     Hash value:   34277d02
     Hash algo:    sha1
     Hash value:   59350071fab74c7ebc25527d129b8df03b928550
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 4007ff28 ...
   Using 'config-1' configuration
   Trying 'fdt-1' fdt subimage
     Description:  ARM64 OpenWrt xiaomi_redmi-router-ax6s device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x4040fec8
     Data Size:    28699 Bytes = 28 KiB
     Architecture: AArch64
     Hash algo:    crc32
     Hash value:   5266c96c
     Hash algo:    sha1
     Hash value:   971ba76339e05a4af50e447c1c18ffe13e6b9242
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x4040fec8
   Uncompressing Kernel Image ... OK
   Loading Device Tree to 4cf39000, end 4cf4301a ... OK

Starting kernel ...

[ATF][     7.822817]save kernel info
[ATF][     7.825753]Kernel_EL2
[ATF][     7.828423]Kernel is 64Bit
[ATF][     7.831511]pc=0x44000000, r0=0x4cf39000, r1=0x0
INFO:    BL3-1: Preparing for EL3 exit to normal world, Kernel
INFO:    BL3-1: Next image address = 0x44000000
INFO:    BL3-1: Next image spsr = 0x3c9
[ATF][     7.849209]el3_exit
Booting Linux on physical CPU 0x0000000000 [0x410fd034]
Linux version 5.10.138 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19685-512e76967f) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Sat Sep 3 02:55:34 2022
Machine model: Xiaomi Redmi Router AX6S
Zone ranges:
  DMA      [mem 0x0000000040000000-0x000000004fffffff]
  DMA32    empty
  Normal   empty
Movable zone start for each node
Early memory node ranges
  node   0: [mem 0x0000000040000000-0x0000000042ffffff]
  node   0: [mem 0x0000000043000000-0x000000004302ffff]
  node   0: [mem 0x0000000043030000-0x000000004fffffff]
Initmem setup node 0 [mem 0x0000000040000000-0x000000004fffffff]
On node 0 totalpages: 65536
  DMA zone: 1024 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 65536 pages, LIFO batch:15
psci: probing for conduit method from DT.
psci: PSCIv0.2 detected in firmware.
psci: Using standard PSCI v0.2 function IDs
psci: Trusted OS migration not required
percpu: Embedded 20 pages/cpu s43992 r8192 d29736 u81920
pcpu-alloc: s43992 r8192 d29736 u81920 alloc=20*4096
pcpu-alloc: [0] 0 [0] 1
Detected VIPT I-cache on CPU0
CPU features: detected: ARM erratum 845719
CPU features: kernel page table isolation disabled by kernel configuration
CPU features: detected: ARM erratum 843419
Built 1 zonelists, mobility grouping on.  Total pages: 64512
Kernel command line: console=ttyS0,115200n1 loglevel=8 swiotlb=512 rootfstype=squashfs firmware=0 uart_en=1
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
mem auto-init: stack:off, heap alloc:off, heap free:off
Memory: 232880K/262144K available (8254K kernel code, 894K rwdata, 1440K rodata, 448K init, 300K bss, 29264K reserved, 0K cma-reserved)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
rcu: Hierarchical RCU implementation.
 Tracing variant of Tasks RCU enabled.
rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
GIC: GICv2 detected, but range too small and irqchip.gicv2_force_probe not set
arch_timer: cp15 timer(s) running at 12.50MHz (phys).
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns
Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
rcu: Hierarchical SRCU implementation.
dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
smp: Bringing up secondary CPUs ...
Detected VIPT I-cache on CPU1
CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
smp: Brought up 1 node, 2 CPUs
SMP: Total of 2 processors activated.
CPU features: detected: 32-bit EL0 Support
CPU features: detected: CRC32 instructions
CPU: All CPU(s) started at EL2
alternatives: patching kernel code
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 512 (order: 3, 32768 bytes, linear)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
thermal_sys: Registered thermal governor 'fair_share'
thermal_sys: Registered thermal governor 'bang_bang'
thermal_sys: Registered thermal governor 'step_wise'
thermal_sys: Registered thermal governor 'user_space'
ASID allocator initialised with 65536 entries
pstore: Registered ramoops as persistent store backend
ramoops: using 0x10000@0x42ff0000, ecc: 0
cryptd: max_cpu_qlen set to 1000
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
clocksource: Switched to clocksource arch_sys_counter
NET: Registered protocol family 2
IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
TCP established hash table entries: 2048 (order: 2, 16384 bytes, linear)
TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
NET: Registered protocol family 1
PCI: CLS 0 bytes, default 64
workingset: timestamp_bits=46 max_order=16 bucket_order=0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
mt-pmic-pwrap 10001000.pwrap: unexpected interrupt int=0x1
Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
printk: console [ttyS0] disabled
11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 21, base_baud = 1562500) is a ST16650V2
printk: console [ttyS0] enabled
mtk_rng 1020f000.rng: registered RNG driver
random: crng init done
cacheinfo: Unable to detect cache hierarchy for CPU 0
loop: module loaded
Loading iSCSI transport class v2.0-870.
mtk-snand 1100d000.snfi: chip is F50L1G41LB, size 128MB, page size 2048, oob size 64
[BBT] BMT.v2 is found at 0x3ff
10 fixed-partitions partitions found on MTD device 1100d000.snfi
Creating 10 MTD partitions on "1100d000.snfi":
0x000000000000-0x000000080000 : "Preloader"
0x000000080000-0x0000000c0000 : "ATF"
0x0000000c0000-0x000000140000 : "u-boot"
0x000000140000-0x000000180000 : "u-boot-env"
0x000000180000-0x0000001c0000 : "bdata"
0x0000001c0000-0x000000240000 : "factory"
0x000000240000-0x000000280000 : "crash"
0x000000280000-0x0000002c0000 : "crash_log"
0x0000002c0000-0x0000006c0000 : "kernel"
no rootfs found after FIT image in "kernel"
0x0000006c0000-0x0000075c0000 : "ubi"
mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xffffffc011c80000, irq 30
i2c /dev entries driver
mtk-wdt 10212000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
NET: Registered protocol family 10
Segment Routing with IPv6
NET: Registered protocol family 17
bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
8021q: 802.1Q VLAN Support v1.8
pstore: Using crash dump compression: deflate
mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges:
mtk-pcie 1a143000.pcie: Parsing ranges property...
mtk-pcie 1a143000.pcie:      MEM 0x0020000000..0x0027ffffff -> 0x0020000000
mtk-pcie 1a143000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [mem 0x20000000-0x27ffffff]
pci_bus 0000:00: scanning bus
pci 0000:00:00.0: [14c3:3258] type 01 class 0x060400
pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x1ffffffff 64bit pref]
pci_bus 0000:00: fixups for bus
pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0
pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1
pci_bus 0000:01: scanning bus
pci 0000:01:00.0: [14c3:7915] type 00 class 0x000280
pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
pci 0000:01:00.0: supports D1 D2
pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
pci_bus 0000:01: fixups for bus
pci_bus 0000:01: bus scan returning with max=01
pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
pci_bus 0000:00: bus scan returning with max=01
pci 0000:00:00.0: BAR 0: no space for [mem size 0x200000000 64bit pref]
pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x200000000 64bit pref]
pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit pref]
pci 0000:01:00.0: BAR 2: assigned [mem 0x20100000-0x20103fff 64bit pref]
pci 0000:01:00.0: BAR 4: assigned [mem 0x20104000-0x20104fff 64bit pref]
pci 0000:00:00.0: PCI bridge to [bus 01]
pci 0000:00:00.0:   bridge window [mem 0x20000000-0x201fffff]
pcieport 0000:00:00.0: of_irq_parse_pci: failed with rc=-22
pcieport 0000:00:00.0: assign IRQ: got 0
pcieport 0000:00:00.0: enabling device (0000 -> 0002)
pcieport 0000:00:00.0: enabling bus mastering
mtk_hsdma 1b007000.dma-controller: Using 3 as missing dma-requests property
mtk_hsdma 1b007000.dma-controller: MediaTek HSDMA driver registered
mt7530 mdio-bus:00 wan (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=138)
mt7530 mdio-bus:00 lan1 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=139)
mt7530 mdio-bus:00 lan2 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=140)
mt7530 mdio-bus:00 lan3 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=141)
mt7530 mdio-bus:00: configuring for fixed/2500base-x link mode
DSA: tree 0 setup
mt7530 mdio-bus:00: Link is Up - 2.5Gbps/Full - flow control rx/tx
UBI: auto-attach mtd9
ubi0: attaching mtd9
ubi0: scanning is finished
ubi0: attached mtd9 (name "ubi", size 111 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 888, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1662173734
ubi0: available PEBs: 0, total reserved PEBs: 888, PEBs reserved for bad PEB handling: 19
ubi0: background thread "ubi_bgt0d" started, PID 763
block ubiblock0_0: created from ubi0:0(rootfs)
ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
VFS: Mounted root (squashfs filesystem) readonly on device 259:0.
Freeing unused kernel memory: 448K
Run /sbin/init as init process
  with arguments:
    /sbin/init
  with environment:
    HOME=/
    TERM=linux
    firmware=0
    uart_en=1
init: Console is alive
init: - watchdog -
kmodloader: loading kernel modules from /etc/modules-boot.d/*
kmodloader: done loading kernel modules from /etc/modules-boot.d/*
init: - preinit -
mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode
8021q: adding VLAN 0 to HW filter on device lan1
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
mt7530 mdio-bus:00 lan1: Link is Up - 1Gbps/Full - flow control rx/tx
IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
UBIFS (ubi0:1): Mounting in unauthenticated mode
UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 842
UBIFS (ubi0:1): recovery needed
UBIFS (ubi0:1): recovery completed
UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:1): FS size: 103231488 bytes (98 MiB, 813 LEBs), journal size 5206016 bytes (4 MiB, 41 LEBs)
UBIFS (ubi0:1): reserved for root: 4875878 bytes (4761 KiB)
UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 1D56BA8C-4CE9-4A65-88F2-ABC1E6F24129, small LPT model
mount_root: switching to ubifs overlay
overlayfs: "xino" feature enabled using 2 upper inode bits.
urandom-seed: Seeding with /etc/urandom.seed
mt7530 mdio-bus:00 lan1: Link is Down
procd: - early -
procd: - watchdog -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
urngd: v1.0.2 started.
kmodloader: loading kernel modules from /etc/modules.d/*
Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064
Backport generated by backports.git v5.15.58-1-0-g42a95ce7
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
mt7915e 0000:01:00.0: assign IRQ: got 142
pci 0000:00:00.0: enabling bus mastering
mt7915e 0000:01:00.0: enabling device (0000 -> 0002)
mt7915e 0000:01:00.0: enabling bus mastering
mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a
[    8.541008]
mt7622-wmac 18000000.wmac: N9 Firmware Version: _reserved_, Build Time: 20220630094834
mt7915e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20211222184017a
[    8.731471]
mt7915e 0000:01:00.0: WM Firmware Version: ____000000, Build Time: 20211222184052
mt7915e 0000:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20211222184111
PPP generic driver version 2.4.2
NET: Registered protocol family 24
kmodloader: done loading kernel modules from /etc/modules.d/*
[   10.675791] mtk_soc_eth 1b100000.ethernet eth0: Link is Down
[   10.684772] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
[   10.693258] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[   10.701988] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   10.712980] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode
[   10.722867] 8021q: adding VLAN 0 to HW filter on device lan1
[   10.731620] br-lan: port 1(lan1) entered blocking state
[   10.736853] br-lan: port 1(lan1) entered disabled state
[   10.744517] device lan1 entered promiscuous mode
[   10.749234] device eth0 entered promiscuous mode
[   10.760191] mt7530 mdio-bus:00 lan2: configuring for phy/gmii link mode
[   10.776804] 8021q: adding VLAN 0 to HW filter on device lan2
[   10.787687] br-lan: port 2(lan2) entered blocking state
[   10.792920] br-lan: port 2(lan2) entered disabled state
[   10.802265] device lan2 entered promiscuous mode
[   10.814022] mt7530 mdio-bus:00 lan3: configuring for phy/gmii link mode
[   10.822525] 8021q: adding VLAN 0 to HW filter on device lan3
[   10.831245] br-lan: port 3(lan3) entered blocking state
[   10.836476] br-lan: port 3(lan3) entered disabled state
[   10.844302] device lan3 entered promiscuous mode
[   10.854103] mt7530 mdio-bus:00 wan: configuring for phy/gmii link mode
[   10.861212] 8021q: adding VLAN 0 to HW filter on device wan
[   10.869162] br-lan: port 4(wan) entered blocking state
[   10.874308] br-lan: port 4(wan) entered disabled state
[   10.880936] device wan entered promiscuous mode
[   12.144964] br-lan: port 5(wlan0-1) entered blocking state
[   12.150560] br-lan: port 5(wlan0-1) entered disabled state
[   12.156274] device wlan0-1 entered promiscuous mode
[   12.161291] br-lan: port 5(wlan0-1) entered blocking state
[   12.166776] br-lan: port 5(wlan0-1) entered forwarding state
[   12.172687] br-lan: port 5(wlan0-1) entered disabled state
[   12.336907] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[   12.343558] br-lan: port 5(wlan0-1) entered blocking state
[   12.349050] br-lan: port 5(wlan0-1) entered forwarding state
[   12.354882] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   13.772289] mt7530 mdio-bus:00 lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[   14.778834] br-lan: port 1(lan1) entered blocking state
[   14.784072] br-lan: port 1(lan1) entered forwarding state
[   14.790108] br-lan: port 6(wlan1-1) entered blocking state
[   14.795613] br-lan: port 6(wlan1-1) entered disabled state
[   14.801344] device wlan1-1 entered promiscuous mode
[   15.097332] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-1: link becomes ready
[   15.103952] br-lan: port 6(wlan1-1) entered blocking state
[   15.109449] br-lan: port 6(wlan1-1) entered forwarding state
[   15.230272] br-lan: port 7(wlan0) entered blocking state
[   15.235588] br-lan: port 7(wlan0) entered disabled state
[   15.241176] device wlan0 entered promiscuous mode
[   15.847034] br-lan: port 5(wlan0-1) entered disabled state
[   16.506313] br-lan: port 8(wlan1) entered blocking state
[   16.511668] br-lan: port 8(wlan1) entered disabled state
[   16.517186] device wlan1 entered promiscuous mode
[   16.678541] br-lan: port 5(wlan0-1) entered blocking state
[   16.684041] br-lan: port 5(wlan0-1) entered forwarding state
[   16.745875] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   16.752369] br-lan: port 7(wlan0) entered blocking state
[   16.757744] br-lan: port 7(wlan0) entered forwarding state
[   16.857225] br-lan: port 6(wlan1-1) entered disabled state
[   17.768776] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:8f, vlan:0)
[   17.785583] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:8f, vlan:0)
[   17.928916] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:8f, vlan:0)
[   18.028470] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:8f, vlan:0)
[   18.781103] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:8f, vlan:0)
[   21.138599] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   21.145146] br-lan: port 8(wlan1) entered blocking state
[   21.150521] br-lan: port 8(wlan1) entered forwarding state
[   21.157484] br-lan: port 6(wlan1-1) entered blocking state
[   21.162978] br-lan: port 6(wlan1-1) entered forwarding state
[   21.768587] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   21.779387] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   21.789829] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   21.790404] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   21.800054] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   22.780977] net_ratelimit: 243 callbacks suppressed
[   22.780984] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   22.783012] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   22.785970] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   22.796115] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   22.806152] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   22.816321] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   22.827130] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   22.836646] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   22.846665] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   22.856881] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   27.788741] net_ratelimit: 1240 callbacks suppressed
[   27.793724] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   27.804095] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   27.804768] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   27.814313] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   27.824387] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   27.834595] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   27.844947] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   27.854990] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   27.875198] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   27.885390] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   32.797660] net_ratelimit: 1551 callbacks suppressed
[   32.802644] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   32.812909] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   32.823104] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   32.833244] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   32.843376] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   32.853507] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   32.863666] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   32.873798] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   32.884063] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   32.894591] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   37.808100] net_ratelimit: 2485 callbacks suppressed
[   37.813086] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   37.823313] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   37.833562] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   37.843719] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   37.853890] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   37.864208] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   37.866554] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   37.874380] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   37.884518] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   37.894602] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   42.818065] net_ratelimit: 2827 callbacks suppressed
[   42.818073] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   42.833666] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   42.843812] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   42.853935] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   42.864103] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   42.874301] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   42.884416] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   42.894535] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   42.905261] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   42.905903] br-lan: received packet on wlan0 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   47.827449] net_ratelimit: 3219 callbacks suppressed
[   47.827457] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   47.827833] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   47.853037] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   47.853182] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   47.863157] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   47.873330] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   47.883401] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   47.893800] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   47.903690] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   47.913839] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   52.839121] net_ratelimit: 3176 callbacks suppressed
[   52.844104] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   52.854264] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   52.854808] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   52.864390] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   52.874569] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   52.884625] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   52.895184] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   52.904900] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   52.915043] br-lan: received packet on wlan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   52.925232] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
^A^C[   57.847793] net_ratelimit: 2753 callbacks suppressed
[   57.847800] br-lan: received packet on wlan0 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   57.849331] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   57.873128] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   57.873389] br-lan: received packet on wlan0 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   57.883247] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   57.893571] br-lan: received packet on wlan0 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   57.903553] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   57.913802] br-lan: received packet on wlan0 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   57.923738] br-lan: received packet on lan1 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
[   57.934003] br-lan: received packet on wlan0 with own address as source address (addr:a4:39:b3:73:76:90, vlan:0)
Please press Enter to activate this console.