Comparar texto

Encontre a diferença entre dois arquivos de texto

Editor live

Ocultar espaços em branco

Recolher inalteradas

Sem quebra de linha

Layout

Nível de detalhe

Estilos de texto

Realce de sintaxe

Diffchecker Desktop A maneira mais segura de usar o Diffchecker. Obtenha o aplicativo Diffchecker Desktop: seus diffs nunca saem do seu computador!Obter Desktop

perfetto config differences

Criado ano passadoO diff nunca expira

41 remoções

Linhas
Total
Removido

Caracteres
Total
Removido

Para continuar usando este recurso, atualize para Diffchecker Pro Ver preços

67 linhas

48 adições

Linhas
Total
Adicionado

Caracteres
Total
Adicionado

Para continuar usando este recurso, atualize para Diffchecker Pro Ver preços

71 linhas

; Configuration file for Duet WiFi (firmware version 2.03)

; executed by the firmware on start-up

;

; generated by RepRapFirmware Configuration Tool v2.1.8 on Sat Apr 04 2020 19:27:02 GMT+0200 (Ora legale dellâ€™Europa centrale)

; generated by RepRapFirmware Configuration Tool v3.4.1 on Sat Apr 26 2025 19:13:09 GMT+0200 (Ora legale dellâ€™Europa centrale)

; General preferences

M575 P1 S1 B57600 ; enable support for PanelDue

G90 ; send absolute coordinates...

M83 ; ...but relative extruder moves

M550 P"My Printer EUGENIO" ; set printer name

M550 P"BAY PRINT EUGENIO" ; set printer name

; Network

M552 P192.168.1.18 S1 ; enable network and set IP address

M553 P255.255.255.0 ; set netmask

M554 P192.168.1.254 ; set gateway

M586 P0 S1 ; enable HTTP

M586 P1 S0 ; disable FTP

M586 P2 S0 ; disable Telnet

; Drives

M569 P0 S0 ; physical drive 0 goes backwards

M569 P1 S0 ; physical drive 1 goes backwards

M569 P2 S0 ; physical drive 2 goes backwards

M569 P3 S0 ; physical drive 3 goes backwards

M569 P3 S1 ; physical drive 3 goes forwards

M584 X0 Y1 Z2 E3 ; set drive mapping

M350 X32 Y32 I0 ; configure microstepping without interpolation

M350 Z16 E16 I1 ; configure microstepping with interpolation

M92 X160.00 Y160.00 Z4000.00 E420.00 ; set steps per mm

M92 X160.00 Y160.00 Z400.00 E84.88 ; set steps per mm

M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)

M566 X12000.00 Y12000.00 Z180.00 E2400.00 ; set maximum instantaneous speed changes (mm/min)

M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)

M203 X36000.00 Y36000.00 Z240.00 E2400.00 ; set maximum speeds (mm/min)

M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)

M201 X1500.00 Y1500.00 Z30.00 E1500.00 ; set accelerations (mm/s^2)

M906 X1300 Y1300 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent

M84 S30 ; Set idle timeout

; Axis Limits

M208 X-10 Y-10 Z0 S1 ; set axis minima

M208 X310 Y310 Z450 S0 ; set axis maxima

; Endstops

M574 X1 Y1 Z1 S0 ; set active low and disabled endstops

M574 X1 Y1 S0 ; set active low and disabled endstops

M574 Z1 S2 ; set endstops controlled by probe

; Z-Probe

M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed

M307 H3 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch

M557 X20:290 Y10:290 S20 ; define mesh grid

M558 P9 H15 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds

M558 H30 ;*** Remove this line after delta calibration has been done and new delta parameters have been saved

G31 P500 X220 Y165 Z3.65 ; set Z probe trigger value, offset and trigger height

M557 X-7:285 Y30:290 S40 ; define mesh grid

; Heaters

M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit

M305 P0 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 0

M143 H0 S120 ; set temperature limit for heater 0 to 120C

M305 P1 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 1

M305 P1 T100000 B4681 C6.463940e-8 R4700 ; set thermistor + ADC parameters for heater 1

M143 H1 S280 ; set temperature limit for heater 1 to 280C

M143 H1 S300 ; set temperature limit for heater 1 to 300C

; Fans

M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off

M106 P0 S0 I0 F500 H1 T45 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on

M106 P1 S1 I0 F500 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools

M563 P0 S"E0" D0 H1 F0 ; define tool 0

M563 P0 D0 H1 F0 ; define tool 0

G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets

G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings

; Custom settings are not defined

M92 E 95.245

; Miscellaneous

M911 S18 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

M501 ; load saved parameters from non-volatile memory

M911 S21 R22 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

Diferenças salvas

Texto original

Abrir arquivo

; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sat Apr 04 2020 19:27:02 GMT+0200 (Ora legale dellâ€™Europa centrale)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"My Printer EUGENIO"                         ; set printer name

; Network
M552 P192.168.1.18 S1                              ; enable network and set IP address
M553 P255.255.255.0                                ; set netmask
M554 P192.168.1.254                                ; set gateway
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet

; Drives
M569 P0 S0                                         ; physical drive 0 goes backwards
M569 P1 S0                                         ; physical drive 1 goes backwards
M569 P2 S0                                         ; physical drive 2 goes backwards
M569 P3 S0                                         ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X32 Y32 I0                                    ; configure microstepping without interpolation
M350 Z16 E16 I1                                    ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z4000.00 E420.00               ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00            ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00                ; set accelerations (mm/s^2)
M906 X1300 Y1300 Z800 E800 I30                     ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X-10 Y-10 Z0 S1                               ; set axis minima
M208 X310 Y310 Z450 S0                             ; set axis maxima

; Endstops
M574 X1 Y1 Z1 S0                                   ; set active low and disabled endstops

; Z-Probe
M558 P0 H5 F120 T6000                              ; disable Z probe but set dive height, probe speed and travel speed
M557 X20:290 Y10:290 S20                           ; define mesh grid

; Heaters
M307 H0 B0 S1.00                                   ; disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4138 R4700                        ; set thermistor + ADC parameters for heater 0
M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700                        ; set thermistor + ADC parameters for heater 1
M143 H1 S280                                       ; set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1                             ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45                          ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 S"E0" D0 H1 F0                             ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings
M92 E 95.245

; Miscellaneous
M911 S18 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

Texto alterado

Abrir arquivo

; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.4.1 on Sat Apr 26 2025 19:13:09 GMT+0200 (Ora legale dellâ€™Europa centrale)

; General preferences
M575 P1 S1 B57600                                  ; enable support for PanelDue
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"BAY PRINT EUGENIO"                          ; set printer name

; Drives
M569 P0 S0                                         ; physical drive 0 goes backwards
M569 P1 S0                                         ; physical drive 1 goes backwards
M569 P2 S0                                         ; physical drive 2 goes backwards
M569 P3 S1                                         ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X32 Y32 I0                                    ; configure microstepping without interpolation
M350 Z16 E16 I1                                    ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z400.00 E84.88                 ; set steps per mm
M566 X12000.00 Y12000.00 Z180.00 E2400.00          ; set maximum instantaneous speed changes (mm/min)
M203 X36000.00 Y36000.00 Z240.00 E2400.00          ; set maximum speeds (mm/min)
M201 X1500.00 Y1500.00 Z30.00 E1500.00             ; set accelerations (mm/s^2)
M906 X1300 Y1300 Z800 E800 I30                     ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X-10 Y-10 Z0 S1                               ; set axis minima
M208 X310 Y310 Z450 S0                             ; set axis maxima

; Endstops
M574 X1 Y1 S0                                      ; set active low and disabled endstops
M574 Z1 S2                                         ; set endstops controlled by probe

; Z-Probe
M307 H3 A-1 C-1 D-1                                ; disable heater on PWM channel for BLTouch
M558 P9 H15 F120 T6000                             ; set Z probe type to bltouch and the dive height + speeds
M558 H30                                           ;*** Remove this line after delta calibration has been done and new delta parameters have been saved
G31 P500 X220 Y165 Z3.65                           ; set Z probe trigger value, offset and trigger height
M557 X-7:285 Y30:290 S40                           ; define mesh grid

; Heaters
M305 P0 T100000 B4138 R4700                        ; set thermistor + ADC parameters for heater 0
M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4681 C6.463940e-8 R4700           ; set thermistor + ADC parameters for heater 1
M143 H1 S300                                       ; set temperature limit for heater 1 to 300C

; Fans
M106 P0 S0 I0 F500 H1 T45                          ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45                          ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                                   ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501                                               ; load saved parameters from non-volatile memory
M911 S21 R22 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss