Compare text

Find the difference between two text files

Real-time diff

Unified diff

Collapse lines

Highlight change

Syntax highlighting

Tools

u-boot diff

Created 10 months agoDiff never expires

61 removals

72 lines

105 additions

136 lines

U-Boot TPL 2022.07-armbian (Jul 12 2023 - 11:15:51)

DDR Version 1.25 20210517

Channel 0: LPDDR4, 50MHz

BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB

channel 0

Channel 1: LPDDR4, 50MHz

CS = 0

BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB

MR0=0x18

MR4=0x1

MR5=0x1

MR8=0x10

MR12=0x72

MR14=0x72

MR18=0x0

MR19=0x0

MR24=0x8

MR25=0x0

channel 1

CS = 0

MR0=0x18

MR4=0x1

MR5=0x1

MR8=0x10

MR12=0x72

MR14=0x72

MR18=0x0

MR19=0x0

MR24=0x8

MR25=0x0

channel 0 training pass!

channel 1 training pass!

change freq to 416MHz 0,1

Channel 0: LPDDR4,416MHz

Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB

Channel 1: LPDDR4,416MHz

Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB

256B stride

lpddr4_set_rate: change freq to 400000000 mhz 0, 1

channel 0

lpddr4_set_rate: change freq to 800000000 mhz 1, 0

CS = 0

Trying to boot from BOOTROM

MR0=0x18

Returning to boot ROM...

MR4=0x1

U-Boot SPL 2022.07-armbian (Jul 12 2023 - 11:15:51 +0000)

MR5=0x1

MR8=0x10

MR12=0x72

MR14=0x72

MR18=0x0

MR19=0x0

MR24=0x8

MR25=0x0

channel 1

CS = 0

MR0=0x18

MR4=0x1

MR5=0x1

MR8=0x10

MR12=0x72

MR14=0x72

MR18=0x0

MR19=0x0

MR24=0x8

MR25=0x0

channel 0 training pass!

channel 1 training pass!

channel 0, cs 0, advanced training done

channel 1, cs 0, advanced training done

change freq to 856MHz 1,0

ch 0 ddrconfig = 0x101, ddrsize = 0x40

ch 1 ddrconfig = 0x101, ddrsize = 0x40

pmugrf_os_reg[2] = 0x32C1F2C1, stride = 0xD

ddr_set_rate to 328MHZ

ddr_set_rate to 666MHZ

ddr_set_rate to 928MHZ

channel 0, cs 0, advanced training done

channel 1, cs 0, advanced training done

ddr_set_rate to 416MHZ, ctl_index 0

ddr_set_rate to 856MHZ, ctl_index 1

support 416 856 328 666 928 MHz, current 856MHz

OUT

U-Boot SPL 2022.07-armbian (Jul 26 2023 - 11:44:56 +0000)

Trying to boot from SPI

Trying to boot from MMC1

Card did not respond to voltage select! : -110

spl: mmc init failed with error: -95

Trying to boot from MMC2

NOTICE: BL31: v2.6(release):armbian

NOTICE: BL31: Built : 11:15:35, Jul 12 2023

NOTICE: BL31: Built : 11:43:56, Jul 26 2023

INFO: GICv3 with legacy support detected.

INFO: ARM GICv3 driver initialized in EL3

INFO: Maximum SPI INTID supported: 287

INFO: plat_rockchip_pmu_init(1624): pd status 3e

INFO: BL31: Initializing runtime services

INFO: BL31: Preparing for EL3 exit to normal world

INFO: Entry point address = 0x200000

INFO: SPSR = 0x3c9

U-Boot 2022.07-armbian (Jul 12 2023 - 11:15:51 +0000)

U-Boot 2022.07-armbian (Jul 26 2023 - 11:44:56 +0000)

SoC: Rockchip rk3399

Reset cause: POR

DRAM: 3.9 GiB

PMIC: RK808

Core: 339 devices, 31 uclasses, devicetree: separate

SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB

MMC: mmc@fe320000: 1, mmc@fe330000: 0

Loading Environment from MMC... *** Warning - bad CRC, using default environment

In: serial

Out: serial

Err: serial

Model: Helios64

Revision: 1.2 - 4GB non ECC

Net: dw_dm_mdio_init: mdio node is missing, registering legacy mdio busNo ethernet found.

scanning bus for devices...

Hit any key to stop autoboot: 0

Card did not respond to voltage select! : -110

switch to partitions #0, OK

mmc0(part 0) is current device

Scanning mmc 0:1...

Found U-Boot script /boot/boot.scr

3252 bytes read in 17 ms (186.5 KiB/s)

3185 bytes read in 19 ms (163.1 KiB/s)

## Executing script at 00500000

Boot script loaded from mmc 0

166 bytes read in 12 ms (12.7 KiB/s)

22364065 bytes read in 2138 ms (10 MiB/s)

18236293 bytes read in 1747 ms (10 MiB/s)

29792768 bytes read in 2838 ms (10 MiB/s)

29295104 bytes read in 2789 ms (10 MiB/s)

86670 bytes read in 38 ms (2.2 MiB/s)

86577 bytes read in 42 ms (2 MiB/s)

2698 bytes read in 29 ms (90.8 KiB/s)

2698 bytes read in 31 ms (85 KiB/s)

Applying kernel provided DT fixup script (rockchip-fixup.scr)

## Executing script at 09000000

Unknown command 'kaslrseed' - try 'help'

Moving Image from 0x2080000 to 0x2200000, end=3e90000

Moving Image from 0x2080000 to 0x2200000, end=3f00000

## Loading init Ramdisk from Legacy Image at 06000000 ...

Image Name: uInitrd

Image Type: AArch64 Linux RAMDisk Image (gzip compressed)

Data Size: 22364001 Bytes = 21.3 MiB

Data Size: 18236229 Bytes = 17.4 MiB

Load Address: 00000000

Entry Point: 00000000

Verifying Checksum ... OK

## Flattened Device Tree blob at 01f00000

Booting using the fdt blob at 0x1f00000

Loading Ramdisk to f4989000, end f5edcf61 ... OK

Loading Ramdisk to f4d79000, end f5edd345 ... OK

Loading Device Tree to 00000000f490b000, end 00000000f4988fff ... OK

Loading Device Tree to 00000000f4cfb000, end 00000000f4d78fff ... OK

Starting kernel ...

Saved diffs

Original text

Open file

U-Boot TPL 2022.07-armbian (Jul 12 2023 - 11:15:51)
Channel 0: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB
Channel 1: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB
256B stride
lpddr4_set_rate: change freq to 400000000 mhz 0, 1
lpddr4_set_rate: change freq to 800000000 mhz 1, 0
Trying to boot from BOOTROM
Returning to boot ROM...
U-Boot SPL 2022.07-armbian (Jul 12 2023 - 11:15:51 +0000)
Trying to boot from SPI
Trying to boot from MMC1
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC2
NOTICE:  BL31: v2.6(release):armbian
NOTICE:  BL31: Built : 11:15:35, Jul 12 2023
INFO:    GICv3 with legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    Maximum SPI INTID supported: 287
INFO:    plat_rockchip_pmu_init(1624): pd status 3e
INFO:    BL31: Initializing runtime services
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9
U-Boot 2022.07-armbian (Jul 12 2023 - 11:15:51 +0000)
SoC: Rockchip rk3399
Reset cause: POR
DRAM:  3.9 GiB
PMIC:  RK808
Core:  339 devices, 31 uclasses, devicetree: separate
SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
MMC:   mmc@fe320000: 1, mmc@fe330000: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment
In:    serial
Out:   serial
Err:   serial
Model: Helios64
Revision: 1.2 - 4GB non ECC
Net:   dw_dm_mdio_init: mdio node is missing, registering legacy mdio busNo ethernet found.
scanning bus for devices...
Hit any key to stop autoboot:  0
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found U-Boot script /boot/boot.scr
3252 bytes read in 17 ms (186.5 KiB/s)
## Executing script at 00500000
Boot script loaded from mmc 0
166 bytes read in 12 ms (12.7 KiB/s)
22364065 bytes read in 2138 ms (10 MiB/s)
29792768 bytes read in 2838 ms (10 MiB/s)
86670 bytes read in 38 ms (2.2 MiB/s)
2698 bytes read in 29 ms (90.8 KiB/s)
Applying kernel provided DT fixup script (rockchip-fixup.scr)
## Executing script at 09000000
Unknown command 'kaslrseed' - try 'help'
Moving Image from 0x2080000 to 0x2200000, end=3f00000
## Loading init Ramdisk from Legacy Image at 06000000 ...
Image Name:   uInitrd
Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
Data Size:    22364001 Bytes = 21.3 MiB
Load Address: 00000000
Entry Point:  00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01f00000
Booting using the fdt blob at 0x1f00000
Loading Ramdisk to f4989000, end f5edcf61 ... OK
Loading Device Tree to 00000000f490b000, end 00000000f4988fff ... OK
Starting kernel ...

Changed text

Open file

DDR Version 1.25 20210517
In
channel 0
CS = 0
MR0=0x18
MR4=0x1
MR5=0x1
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 1
CS = 0
MR0=0x18
MR4=0x1
MR5=0x1
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 0 training pass!
channel 1 training pass!
change freq to 416MHz 0,1
Channel 0: LPDDR4,416MHz
Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB
Channel 1: LPDDR4,416MHz
Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB
256B stride
channel 0
CS = 0
MR0=0x18
MR4=0x1
MR5=0x1
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 1
CS = 0
MR0=0x18
MR4=0x1
MR5=0x1
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 0 training pass!
channel 1 training pass!
channel 0, cs 0, advanced training done
channel 1, cs 0, advanced training done
change freq to 856MHz 1,0
ch 0 ddrconfig = 0x101, ddrsize = 0x40
ch 1 ddrconfig = 0x101, ddrsize = 0x40
pmugrf_os_reg[2] = 0x32C1F2C1, stride = 0xD
ddr_set_rate to 328MHZ
ddr_set_rate to 666MHZ
ddr_set_rate to 928MHZ
channel 0, cs 0, advanced training done
channel 1, cs 0, advanced training done
ddr_set_rate to 416MHZ, ctl_index 0
ddr_set_rate to 856MHZ, ctl_index 1
support 416 856 328 666 928 MHz, current 856MHz
OUT
U-Boot SPL 2022.07-armbian (Jul 26 2023 - 11:44:56 +0000)
Trying to boot from SPI
Trying to boot from MMC1
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC2
NOTICE: BL31: v2.6(release):armbian
NOTICE: BL31: Built : 11:43:56, Jul 26 2023
INFO: GICv3 with legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: Maximum SPI INTID supported: 287
INFO: plat_rockchip_pmu_init(1624): pd status 3e
INFO: BL31: Initializing runtime services
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
U-Boot 2022.07-armbian (Jul 26 2023 - 11:44:56 +0000)
SoC: Rockchip rk3399
Reset cause: POR
DRAM: 3.9 GiB
PMIC: RK808
Core: 339 devices, 31 uclasses, devicetree: separate
SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
MMC: mmc@fe320000: 1, mmc@fe330000: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Model: Helios64
Revision: 1.2 - 4GB non ECC
Net: dw_dm_mdio_init: mdio node is missing, registering legacy mdio busNo ethernet found.
scanning bus for devices...
Hit any key to stop autoboot: 0
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found U-Boot script /boot/boot.scr
3185 bytes read in 19 ms (163.1 KiB/s)
## Executing script at 00500000
Boot script loaded from mmc 0
166 bytes read in 12 ms (12.7 KiB/s)
18236293 bytes read in 1747 ms (10 MiB/s)
29295104 bytes read in 2789 ms (10 MiB/s)
86577 bytes read in 42 ms (2 MiB/s)
2698 bytes read in 31 ms (85 KiB/s)
Applying kernel provided DT fixup script (rockchip-fixup.scr)
## Executing script at 09000000
Moving Image from 0x2080000 to 0x2200000, end=3e90000
## Loading init Ramdisk from Legacy Image at 06000000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
Data Size: 18236229 Bytes = 17.4 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01f00000
Booting using the fdt blob at 0x1f00000
Loading Ramdisk to f4d79000, end f5edd345 ... OK
Loading Device Tree to 00000000f4cfb000, end 00000000f4d78fff ... OK
Starting kernel ...