Confronta il testo

Trova la differenza tra due file di testo

Editor live

Nascondi spazi bianchi

Comprimi invariate

Senza a capo

Layout

Livello di dettaglio

Stili testo

Evidenziazione sintassi

Diffchecker Desktop Il modo più sicuro per usare Diffchecker. Ottieni l'app Diffchecker Desktop: i tuoi diff non lasciano mai il tuo computer!Ottieni Desktop

config.g

Creato 2 anni faIl diff non scade mai

83 rimozioni

Linee
Totale
Rimosso

Caratteri
Totale
Rimosso

Per continuare a utilizzare questa funzione, aggiorna a Diffchecker Pro Visualizza prezzi

175 linee

172 aggiunte

Linee
Totale
Aggiunto

Caratteri
Totale
Aggiunto

Per continuare a utilizzare questa funzione, aggiorna a Diffchecker Pro Visualizza prezzi

207 linee

; =========================================================================================================

;

; Configuration file for Duet2WiFi-Ethernet (firmware version 3.4)

; Configuration file for Duet2-WiFi/Ethernet (firmware version 3.4 and higher)

;

; for 0.9° motors on xy, and 0.9° or 1.8° (only LGXM) motor e

;

; for Caribou320 Duet2WiFi-Ethernet LGX Copperhead - E3d or SE Thermistor - PINDA2

; for Caribou320 Duet2 WiFi/Ethernet LGX Copperhead - E3d or SE Thermistor - PINDA2

;

; CariboDuetConfiguration Release : "1.8.0"

; CariboDuetConfiguration Release : "2.2.0"

; Build : 263

; Build : 587

;

; Copyright Caribou Research & Development 2023. Licensed under GPL3. No commercial use.

; Source code and release notes are available on github: https://github.com/Caribou3d/CaribouDuet2-ConfigurationMacros

;

; Copyright Caribou Research & Development 2021. Licensed under GPL3.

; =========================================================================================================

; Source code and release notes are available on github: https://github.com/Caribou3d/CaribouDuet2Wifi-ConfigurationMacros

;

; general settings

;

M111 S0 ; debugging off

G21 ; work in millimetres

;

; global variables

;

M98 P"0:/settings/Set-Global-Variables.g" ; set global variables

;

; =========================================================================================================

; Network settings

; network settings

; =========================================================================================================

;

M550 P"Caribou320-LGXC-NP" ; set printer name

;

;M552 S1 ; enable network

if {network.interfaces[0].type = "ethernet"}

M586 P0 S1 ; enable HTTP

echo >"0:/sys/runonce.g" "M98 P""0:/settings/Set-Ethernet-Mode.g"""

M586 P1 S1 ; enable FTP

else

M586 P2 S0 ; disable Telnet

M98 P"0:/settings/Set-WiFi-mode.g"

M575 P1 S1 B57600 ; enable support for PanelDue

;

M586 P0 S1 ; enable HTTP

M586 P1 S1 ; enable FTP

M586 P2 S0 ; disable Telnet

M575 P1 S1 B57600 ; enable support for PanelDue

;

; =========================================================================================================

; Drives

; drives

; =========================================================================================================

;

M569 P0 S1 F11 ; physical drive 0 goes forwards - x-axis

M569 P0 S0 F11 ; physical drive 0 goes backwards - x axis

M569 P1 S0 F8 Y3:2 ; physical drive 1 goes backwards - y-axis ;

M569 P1 S0 F8 Y3:2 ; physical drive 1 goes backwards - y axis

M569 P2 S1 F10 ; physical drive 2 goes forwards - z - left

M569 P2 S0 F10 ; physical drive 2 goes backwards - z axis left

M569 P3 S1 F14 ; physical drive 3 goes forwards - Extruder

M569 P3 S1 F14 ; physical drive 3 goes forwards - extruder

M569 P4 S1 F10 ; physical drive 4 goes forwards - z right

M569 P4 S0 F10 ; physical drive 4 goes backwards - z axis right

;

; Motor Configuration

; motor configuration

;

M584 X0 Y1 Z2:4 E3 ; set drive mapping

M671 X-36.5:293.5 Y0:0 S3.00 ; leadscrews at left (connected to Z) and right (connected to E1) of X axis

M671 X-36.5:293.5 Y0:0 S1.00 ; leadscrews at left (connected to Z/drive 2) and right (connected to E1/drive 4) of x axis

;

; set Microsteps and steps / mm

; set microsteps and steps / mm

; =========================================================================================================

;

M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation

M92 X200.00 Y100.00 Z400.0 E829.80 ; set steps per mm

M92 X200.00 Y200.00 Z400.00 ; set steps per mm

M98 P"0:/settings/Set-E-Steps.g" ; set esteps

;

; set motor currents

; =========================================================================================================

;

M906 X1250 Y1250 Z950 E650 I40 ; set motor currents (mA) and motor idle factor in percent

M906 X1250 Y1250 Z650 E650 I40 ; set motor currents (mA) and motor idle factor in percent

;

M84 S60 ; Set idle timeout

M84 S60 ; set idle timeout

;

; set speeds

; =========================================================================================================

;

M201 X500.00 Y500.00 Z100.00 E500.00 ; set accelerations (mm/s^2)

M201 X3000.00 Y3000.00 Z100.00 E500.00 ; set accelerations (mm/s^2)

M203 X9000.00 Y9000.00 Z300.00 E3600.00 ; set maximum speeds (mm/min)

M203 X18000.00 Y18000.00 Z1000.00 E3600.00 ; set maximum speeds (mm/min)

M204 P500.0 T500.0 ; set print and travel accelerations (mm(s^2)

M204 P500.0 T500.0 ; set print and travel accelerations (mm/s^2)

M566 X480.00 Y480.00 Z48.00 E300.00 ; set maximum instantaneous speed changes (mm/min)

;

M564 H0 ; allow unhomed movement

set global.x_accel = move.axes[0].acceleration ; save accelerations (mm/s^2)

set global.x_jerk = move.axes[0].jerk ; save maximum instantaneous speed changes (mm/min)

;

set global.y_accel = move.axes[1].acceleration ; save accelerations (mm/s^2)

set global.y_jerk = move.axes[1].jerk ; save maximum instantaneous speed changes (mm/min)

;

M564 H0 ; allow unhomed movement

;

; =========================================================================================================

; Axis Limits

; axes limits

; =========================================================================================================

;

M208 X-2 Y-7.5 Z0 S1 ; set axis minima

M208 X-2 Y-7.5 Z0 S1 ; set axes minimum

M208 X254.6 Y214 Z325.50 S0 ; set axis maxima

M208 X253.5 Y214 Z325.50 S0 ; set axes maximum

;

; =========================================================================================================

; Endstops

; endstops

; =========================================================================================================

;

M574 X1 S3 ; configure sensorless endstop for low end on x

M574 Y1 S3 ; configure sensorless endstop for low end on y

M574 Z1 S2 ; configure z-probe endstop for low end on z

M574 Z2 S3 ; configure sensorless endstop for high end on z

;

; =========================================================================================================

;

; PINDA2

;

M558 P5 C"^zprobe.in" H1.5 F600 T8000 A3 S0.03 ; set z probe to PINDA2

M308 S2 P"e1temp" A"Pinda V2" Y"thermistor" T100000 B3950 ; temperature of PINDA2

M557 X23:235 Y5:186 S30.25:30 ; define mesh grid

;

; =========================================================================================================

;

M574 Z1 S2 ; set endstops controlled by probe

;

; Stallguard Sensitivy

; stallguard sensitivy

;

M915 X S2 F0 H400 R0 ; set X axis Sensitivity

M915 X S2 F0 H400 R0 ; set x axis sensitivity

M915 Y S0 F0 H200 R0 ; set Y axis Sensitivity

M915 Y S1 F0 H400 R0 ; set y axis sensitivity

M915 Z S0 F0 H200 R0 ; set Z axis Sensitivity

M915 Z S0 F0 H200 R0 ; set z axis sensitivity

;

; =========================================================================================================

; Heater & Fans

; heaters, fans, thermistors

; =========================================================================================================

;

; heated bed

; =========================================================================================================

;

M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 R4700 A"Bed" ; configure sensor 0 as thermistor on pin bedtemp

M950 H0 C"bedheat" Q50 T0 ; create bed heater output on bedheat and map it to sensor 0

M143 H0 S110 ; set temperature limit for heater 0 to 110C

M143 H0 S110 ; set temperature limit for heater 0 to 110°C

M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit

M140 H0 ; map heated bed to heater 0

;

; extruder

; =========================================================================================================

;

; Hotend (Mosquito or Mosquito Magnum with E3d Thermistor)

; hotend (Mosquito or Mosquito Magnum with E3d Thermistor)

;

M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.060000e-8 A"Nozzle E1" ; E3d configure sensor 0 as thermistor on pin e0temp

M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.060000e-8 A"Nozzle E1"; E3d configure sensor 0 as thermistor on pin e0temp

;

M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 2

M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1

M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

M307 H1 B0 S1.00 ; disable bang-bang mode for heater 1 and set PWM limit

M143 H1 S300 ; set temperature limit for heater 1 to 300°C

M143 H1 S280 ; set temperature limit for heater 1 to 280°C

;

; display MCU and drivers temperature

; =========================================================================================================

;

M308 S4 P"mcu-temp" Y"mcu-temp" A"MCU" ; set virtual heater for MCU

M308 S5 P"drivers" Y"drivers" A"Driver" ; set virtual heater for stepper drivers

;

; =========================================================================================================

; fans

; Fans

; =========================================================================================================

;

; extruder fan (temerature controlled)

;

M950 F1 C"fan0" Q500 ; create fan 1 on pin fan0 and set its frequency

M106 P1 H1 T45 ; fan turns on at 45°C

;

; radial fan

;

M950 F0 C"fan1" Q160 ; create fan 0 on pin fan1 and set its frequency

M950 F0 C"fan0" Q160 ; create fan 0 on pin fan1 and set its frequency

M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off

;

; extruder fan (temperature controlled)

;

M950 F1 C"fan1" Q500 ; create fan 1 on pin fan0 and set its frequency

M106 P1 H1 T45 ; fan turns on at 45°C

;

; ========================================================================================================

; Tools

; tools

; =========================================================================================================

;

M563 P0 D0 H1 F0 ; define tool 0

G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets

G10 P0 S-274 R-274 ; turn off tool 0, set active and standby temperature to 0K

M568 P0 S0 R0 A0 ; turn off extruder

M302 S180 R180 ; allow extrusion starting from 180°C and retractions already from 180°C

;

; =========================================================================================================

; other settings

; =========================================================================================================

;

M18 XY ; release / unlock x, y

M98 P"0:/settings/Set-PID-Bed.g" ; set PID values for the heated bed

M501 ; use config-override (for Thermistor Parameters and other settings)

M98 P"0:/settings/Set-PID-Nozzle.g" ; set PID values for the nozzle

G90 ; send absolute coordinates...

M83 ; ... but relative extruder moves

;

; =========================================================================================================

; filament handling

; =========================================================================================================

;

; execute macros that determine the status of the filament sensor

;

M98 P"0:/sys/00-Functions/FilamentsensorStatus"

M98 P"0:/settings/Set-FilamentSensorStatus.g" ; load filament sensor settings

M98 P"0:/settings/Set-AutoLoadStatus.g" ; load autoload settings

M98 P"0:/sys/00-Functions/FilamentsensorStatus" ; update sensor status

;

; =========================================================================================================

;

; offsets - place off-sets for x and y here. z-offsets are handled in the print sheet macros

; =========================================================================================================

;

; Offsets - place off-sets for x and y here. z-offsets are handled in the print sheet macros

M98 P"0:/settings/Set-Probe-XY-Offsets.g" ; set probe xy-offset

M98 P"0:/settings/Set-Probe-Z-Offset.g" ; set probe z-offset

M18 XY ; release / unlock x, y

G90 ; send absolute coordinates...

M83 ; ... but relative extruder moves

;

G31 P1000 X23 Y5 Z1.154

; =========================================================================================================

; check connectivity

; =========================================================================================================

;

if {network.interfaces[0].type = "wifi"}

echo >"0:/sys/runonce.g" "M98 P""0:/sys/test-WiFi.g"""

;

; =========================================================================================================

;

Diff salvati

Testo originale

Apri file

; =========================================================================================================
;
; Configuration file for Duet2WiFi-Ethernet (firmware version 3.4)
;
; for 0.9° motors on xy, and 0.9° or 1.8° (only LGXM) motor e
;
; for Caribou320 Duet2WiFi-Ethernet LGX Copperhead - E3d or SE Thermistor - PINDA2
;
; CariboDuetConfiguration Release : "1.8.0"
;                           Build :   263
;
;
; Copyright Caribou Research & Development 2021. Licensed under GPL3.
; Source code and release notes are available on github: https://github.com/Caribou3d/CaribouDuet2Wifi-ConfigurationMacros
;
; =========================================================================================================
; Network settings
; =========================================================================================================
;
M550 P"Caribou320-LGXC-NP"                                 ; set printer name
;
;M552 S1                                                ; enable network
M586 P0 S1                                             ; enable HTTP
M586 P1 S1                                             ; enable FTP
M586 P2 S0                                             ; disable Telnet
M575 P1 S1 B57600                                      ; enable support for PanelDue
;
; =========================================================================================================
; Drives
; =========================================================================================================
;
M569 P0 S1 F11                                         ; physical drive 0 goes forwards - x-axis
M569 P1 S0 F8 Y3:2                                     ; physical drive 1 goes backwards - y-axis ;
M569 P2 S1 F10                                         ; physical drive 2 goes forwards - z - left
M569 P3 S1 F14                                         ; physical drive 3 goes forwards  - Extruder
M569 P4 S1 F10                                         ; physical drive 4 goes forwards - z right
;
; Motor Configuration
;
M584 X0 Y1 Z2:4 E3                                     ; set drive mapping
M671 X-36.5:293.5 Y0:0 S3.00                           ; leadscrews at left (connected to Z) and right (connected to E1) of X axis
;
; set Microsteps and steps / mm
;
M350 X16 Y16 Z16 E16 I1                                ; configure microstepping with interpolation
M92 X200.00 Y100.00 Z400.0 E829.80                     ; set steps per mm
;
; set motor currents
;
M906 X1250 Y1250 Z950 E650 I40                         ; set motor currents (mA) and motor idle factor in percent 
;
M84 S60                                                ; Set idle timeout
;
; set speeds
;
M201 X500.00 Y500.00 Z100.00 E500.00                   ; set accelerations (mm/s^2)
M203 X9000.00 Y9000.00 Z300.00 E3600.00               ; set maximum speeds (mm/min)
M204 P500.0 T500.0                                     ; set print and travel accelerations (mm(s^2)
M566 X480.00 Y480.00 Z48.00 E300.00                    ; set maximum instantaneous speed changes (mm/min)
;
M564 H0                                                ; allow unhomed movement
;
; =========================================================================================================
; Axis Limits
; =========================================================================================================
;
M208 X-2 Y-7.5 Z0 S1                                   ; set axis minima
M208 X254.6 Y214 Z325.50 S0                            ; set axis maxima
;
; =========================================================================================================
; Endstops
; =========================================================================================================
;
M574 X1 S3                                             ; configure sensorless endstop for low end on x
M574 Y1 S3                                             ; configure sensorless endstop for low end on y
M574 Z1 S2                                             ; configure z-probe endstop for low end on z
M574 Z2 S3                                             ; configure sensorless endstop for high end on z
;
; =========================================================================================================
;
; PINDA2 
;
M558 P5 C"^zprobe.in" H1.5 F600 T8000 A3 S0.03              ; set z probe to PINDA2
M308 S2 P"e1temp" A"Pinda V2" Y"thermistor" T100000 B3950   ; temperature of PINDA2
M557 X23:235 Y5:186 S30.25:30                               ; define mesh grid
;
; =========================================================================================================
;
M574 Z1 S2                                             ; set endstops controlled by probe
;
; Stallguard Sensitivy
;
M915 X S2 F0 H400 R0                                   ; set X axis Sensitivity
M915 Y S0 F0 H200 R0                                   ; set Y axis Sensitivity
M915 Z S0 F0 H200 R0                                   ; set Z axis Sensitivity
;
; =========================================================================================================
; Heater & Fans
; =========================================================================================================
;
; heated bed
; =========================================================================================================
;
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 R4700 A"Bed"  ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" Q50 T0                                    ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S110                                                 ; set temperature limit for heater 0 to 110C
M307 H0 B0 S1.00                                             ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                                      ; map heated bed to heater 0
;
; extruder
; =========================================================================================================
;
; Hotend (Mosquito or Mosquito Magnum with E3d Thermistor) 
;
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.060000e-8 A"Nozzle E1"  ; E3d configure sensor 0 as thermistor on pin e0temp
;
M950 H1 C"e0heat" T1                                        ; create nozzle heater output on e0heat and map it to sensor 2
M307 H1 B0 S1.00                                            ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S300                                              ; set temperature limit for heater 1 to 300°C
;
; =========================================================================================================
;
M308 S4 P"mcu-temp" Y"mcu-temp" A"MCU"                 ; set virtual heater for MCU
M308 S5 P"drivers" Y"drivers" A"Driver"                ; set virtual heater for stepper drivers
;
; =========================================================================================================
; Fans
; =========================================================================================================
;
; extruder fan (temerature controlled)
;
M950 F1 C"fan0" Q500                                   ; create fan 1 on pin fan0 and set its frequency
M106 P1 H1 T45                                         ; fan turns on at 45°C
;
; radial fan
;
M950 F0 C"fan1" Q160                                   ; create fan 0 on pin fan1 and set its frequency
M106 P0 S0 H-1                                         ; set fan 0 value. Thermostatic control is turned off
;
; ========================================================================================================
; Tools
; =========================================================================================================
;
M563 P0 D0 H1 F0                                       ; define tool 0
G10 P0 X0 Y0 Z0                                        ; set tool 0 axis offsets
G10 P0 S-274 R-274                                     ; turn off tool 0, set active and standby temperature to 0K
M302 S180 R180                                         ; allow extrusion starting from 180°C and retractions already from 180°C
;
; =========================================================================================================
; other settings
; =========================================================================================================
;
M18 XY                                                 ; release / unlock x, y
M501                                                   ; use config-override (for Thermistor Parameters and other settings)
G90                                                    ; send absolute coordinates...
M83                                                    ; ... but relative extruder moves
;
; =========================================================================================================
;  filament handling
; =========================================================================================================
;
; execute macros that determine the status of the filament sensor
;
M98 P"0:/sys/00-Functions/FilamentsensorStatus"
;
; =========================================================================================================
;
; =========================================================================================================
;
; Offsets - place off-sets for x and y here. z-offsets are handled in the print sheet macros
;
G31 P1000 X23 Y5 Z1.154
;
; =========================================================================================================
;

Testo modificato

Apri file

; =========================================================================================================
;
; Configuration file for Duet2-WiFi/Ethernet (firmware version 3.4 and higher)
;
; for 0.9° motors on xy, and 0.9° or 1.8° (only LGXM) motor e
;
; for Caribou320 Duet2 WiFi/Ethernet LGX Copperhead - E3d or SE Thermistor - PINDA2
;
; CariboDuetConfiguration Release : "2.2.0"
;                           Build :   587
;
; Copyright Caribou Research & Development 2023. Licensed under GPL3. No commercial use.
; Source code and release notes are available on github: https://github.com/Caribou3d/CaribouDuet2-ConfigurationMacros
;
; =========================================================================================================
;
; general settings
;
M111 S0                                                                ; debugging off
G21                                                                    ; work in millimetres
;
; global variables
;
M98 P"0:/settings/Set-Global-Variables.g"                              ; set global variables
;
; =========================================================================================================
; network settings
; =========================================================================================================
;
M550 P"Caribou320-LGXC-NP"                                             ; set printer name
;
if {network.interfaces[0].type = "ethernet"}
  echo >"0:/sys/runonce.g" "M98 P""0:/settings/Set-Ethernet-Mode.g"""
else
  M98 P"0:/settings/Set-WiFi-mode.g"
;
M586 P0 S1                                                             ; enable HTTP
M586 P1 S1                                                             ; enable FTP
M586 P2 S0                                                             ; disable Telnet
M575 P1 S1 B57600                                                      ; enable support for PanelDue
;
; =========================================================================================================
; drives
; =========================================================================================================
;
M569 P0 S0 F11                                                         ; physical drive 0 goes backwards - x axis
M569 P1 S0 F8 Y3:2                                                     ; physical drive 1 goes backwards - y axis
M569 P2 S0 F10                                                         ; physical drive 2 goes backwards - z axis left
M569 P3 S1 F14                                                         ; physical drive 3 goes forwards  - extruder
M569 P4 S0 F10                                                         ; physical drive 4 goes backwards - z axis right
;
; motor configuration
;
M584 X0 Y1 Z2:4 E3                                                     ; set drive mapping
M671 X-36.5:293.5 Y0:0 S1.00                                           ; leadscrews at left (connected to Z/drive 2) and right (connected to E1/drive 4) of x axis
;
; set microsteps and steps / mm
; =========================================================================================================
;
M350 X16 Y16 Z16 E16 I1                                                ; configure microstepping with interpolation
M92 X200.00 Y200.00 Z400.00                                            ; set steps per mm
M98 P"0:/settings/Set-E-Steps.g"                                       ; set esteps
;
; set motor currents
; =========================================================================================================
;
M906 X1250 Y1250 Z650 E650 I40                                         ; set motor currents (mA) and motor idle factor in percent
;
M84 S60                                                                ; set idle timeout
;
; set speeds
; =========================================================================================================
;
M201 X3000.00 Y3000.00 Z100.00 E500.00                                 ; set accelerations (mm/s^2)
M203 X18000.00 Y18000.00 Z1000.00 E3600.00                             ; set maximum speeds (mm/min)
M204 P500.0 T500.0                                                     ; set print and travel accelerations (mm/s^2)
M566 X480.00 Y480.00 Z48.00 E300.00                                    ; set maximum instantaneous speed changes (mm/min)
;
set global.x_accel = move.axes[0].acceleration                         ; save accelerations (mm/s^2)
set global.x_jerk = move.axes[0].jerk                                  ; save maximum instantaneous speed changes (mm/min)
;
set global.y_accel = move.axes[1].acceleration                         ; save accelerations (mm/s^2)
set global.y_jerk = move.axes[1].jerk                                  ; save maximum instantaneous speed changes (mm/min)
;
M564 H0                                                                ; allow unhomed movement
;
; =========================================================================================================
; axes limits
; =========================================================================================================
;
M208 X-2 Y-7.5 Z0 S1                                                   ; set axes minimum
M208 X253.5 Y214 Z325.50 S0                                            ; set axes maximum
;
; =========================================================================================================
; endstops
; =========================================================================================================
;
M574 X1 S3                                                             ; configure sensorless endstop for low end on x
M574 Y1 S3                                                             ; configure sensorless endstop for low end on y
M574 Z1 S2                                                             ; configure z-probe endstop for low end on z
;
; =========================================================================================================
;
; PINDA2
;
M558 P5 C"^zprobe.in" H1.5 F600 T8000 A3 S0.03                         ; set z probe to PINDA2
M308 S2 P"e1temp" A"Pinda V2" Y"thermistor" T100000 B3950              ; temperature of PINDA2
M557 X23:235 Y5:186 S30.25:30                                          ; define mesh grid
;
; =========================================================================================================
;
M574 Z1 S2                                                             ; set endstops controlled by probe
;
; stallguard sensitivy
;
M915 X S2 F0 H400 R0                                                   ; set x axis sensitivity
M915 Y S1 F0 H400 R0                                                   ; set y axis sensitivity
M915 Z S0 F0 H200 R0                                                   ; set z axis sensitivity
;
; =========================================================================================================
; heaters, fans, thermistors
; =========================================================================================================
;
; heated bed
; =========================================================================================================
;
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 R4700 A"Bed"            ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" Q50 T0                                              ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S110                                                           ; set temperature limit for heater 0 to 110°C
M307 H0 B0 S1.00                                                       ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                                                ; map heated bed to heater 0
;
; extruder
; =========================================================================================================
;
; hotend (Mosquito or Mosquito Magnum with E3d Thermistor)
;
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.060000e-8 A"Nozzle E1"; E3d configure sensor 0 as thermistor on pin e0temp
;
M950 H1 C"e0heat" T1                                                   ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                                                       ; disable bang-bang mode for heater 1 and set PWM limit
M143 H1 S280                                                           ; set temperature limit for heater 1 to 280°C
;
; display MCU and drivers temperature
; =========================================================================================================
;
M308 S4 P"mcu-temp" Y"mcu-temp" A"MCU"                                 ; set virtual heater for MCU
M308 S5 P"drivers" Y"drivers" A"Driver"                                ; set virtual heater for stepper drivers
;
; fans
; =========================================================================================================
;
; radial fan
;
M950 F0 C"fan0" Q160                                                   ; create fan 0 on pin fan1 and set its frequency
M106 P0 S0 H-1                                                         ; set fan 0 value. Thermostatic control is turned off
;
; extruder fan (temperature controlled)
;
M950 F1 C"fan1" Q500                                                   ; create fan 1 on pin fan0 and set its frequency
M106 P1 H1 T45                                                         ; fan turns on at 45°C
;
; ========================================================================================================
; tools
; =========================================================================================================
;
M563 P0 D0 H1 F0                                                       ; define tool 0
G10 P0 X0 Y0 Z0                                                        ; set tool 0 axis offsets
M568 P0 S0 R0 A0                                                       ; turn off extruder
M302 S180 R180                                                         ; allow extrusion starting from 180°C and retractions already from 180°C
;
; =========================================================================================================
; other settings
; =========================================================================================================
;
M98 P"0:/settings/Set-PID-Bed.g"                                       ; set PID values for the heated bed
M98 P"0:/settings/Set-PID-Nozzle.g"                                    ; set PID values for the nozzle
;
; =========================================================================================================
; filament handling
; =========================================================================================================
;
; execute macros that determine the status of the filament sensor
;
M98 P"0:/settings/Set-FilamentSensorStatus.g"                          ; load filament sensor settings
M98 P"0:/settings/Set-AutoLoadStatus.g"                                ; load autoload settings
M98 P"0:/sys/00-Functions/FilamentsensorStatus"                        ; update sensor status
;
; =========================================================================================================
; offsets - place off-sets for x and y here. z-offsets are handled in the print sheet macros
; =========================================================================================================
;
M98 P"0:/settings/Set-Probe-XY-Offsets.g"                              ; set probe xy-offset
M98 P"0:/settings/Set-Probe-Z-Offset.g"                                ; set probe z-offset
M18 XY                                                                 ; release / unlock x, y
G90                                                                    ; send absolute coordinates...
M83                                                                    ; ... but relative extruder moves
;
; =========================================================================================================
; check connectivity
; =========================================================================================================
;
if {network.interfaces[0].type = "wifi"}
  echo >"0:/sys/runonce.g" "M98 P""0:/sys/test-WiFi.g"""
;
; =========================================================================================================
;