Compare text

Find the difference between two text files

Real-time diff

Unified diff

Collapse lines

Highlight change

Syntax highlighting

Tools

Diffchecker Desktop The most secure way to run Diffchecker. Get the Diffchecker Desktop app: your diffs never leave your computer!Get Desktop

WCNSS_qcom_cfg.ini

Created 3 years agoDiff never expires

Lines
Total
Removed

Words
Total
Removed

To continue using this feature, upgrade to Diffchecker Pro View Pricing

408 lines

Lines
Total
Added

Words
Total
Added

To continue using this feature, upgrade to Diffchecker Pro View Pricing

458 lines

# This file allows user to override the factory

# defaults for the WLAN Driver

# Enable IMPS or not

gEnableImps=1

# Enable/Disable Idle Scan

gEnableIdleScan=0

# Increase sleep duration (seconds) during IMPS

# 0 implies no periodic wake up from IMPS. Periodic wakeup is

# unnecessary if Idle Scan is disabled.

gImpsModSleepTime=0

# Enable BMPS or not

gEnableBmps=1

# Enable suspend or not

# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter

gEnableSuspend=3

# Phy Mode (auto, b, g, n, etc)

# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac

gDot11Mode=0

# CSR Roaming Enable(1) Disable(0)

gRoamingTime=0

# Assigned MAC Addresses - This will be used until NV items are in place

# Each byte of MAC address is represented in Hex format as XX

Intf0MacAddress=000AF58989FF

Intf1MacAddress=000AF58989FE

Intf2MacAddress=000AF58989FD

Intf3MacAddress=000AF58989FC

# Set/Clear UAPSD mask

UapsdMask=0

# UAPSD service interval for VO,VI, BE, BK traffic

InfraUapsdVoSrvIntv=20

InfraUapsdVoSrvIntv=0

InfraUapsdViSrvIntv=0

InfraUapsdViSrvIntv=40

InfraUapsdBeSrvIntv=0

InfraUapsdBkSrvIntv=0

# Flag to allow STA send AddTspec even when ACM is Off

gAddTSWhenACMIsOff=1

# Make 1x1 the default antenna configuration

gNumRxAnt=1

# Beacon filtering frequency (unit in beacon intervals)

gNthBeaconFilter=50

# Enable WAPI or not

# WAPIIsEnabled=0

# Flags to filter Mcast abd Bcast RX packets.

# Value 0: No filtering, 1: Filter all Multicast.

# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast

McastBcastFilter=3

#Flag to enable HostARPOffload feature or not

hostArpOffload=1

#SoftAP Related Parameters

# AP MAc addr

gAPMacAddr=000AF589dcab

# 802.11n Protection flag

gEnableApProt=1

#Enable OBSS protection

gEnableApOBSSProt=1

#Enable/Disable UAPSD for SoftAP

gEnableApUapsd=1

# Fixed Rate

gFixedRate=0

# Maximum Tx power

# gTxPowerCap=4

# gTxPowerCap=30

# Fragmentation Threshold

# gFragmentationThreshold=2346

# RTS threshold

RTSThreshold=2346

RTSThreshold=1048576

# Intra-BSS forward

gDisableIntraBssFwd=0

# WMM Enable/Disable

WmmIsEnabled=0

# 802.11d support

g11dSupportEnabled=0

# CCX Support and fast transition

EseEnabled=0

FastTransitionEnabled=1

ImplicitQosIsEnabled=0

gNeighborScanTimerPeriod=200

# default value of this parameter is zero to enable dynamic threshold allocation

# to set static roming threshold uncomment below parameter and set vaule

#gNeighborLookupThreshold=78

# gNeighborLookupThreshold=85

gNeighborScanChannelMinTime=20

gNeighborScanChannelMaxTime=30

gMaxNeighborReqTries=3

# Legacy (non-CCX, non-802.11r) Fast Roaming Support

# To enable, set FastRoamEnabled=1

# To disable, set FastRoamEnabled=0

FastRoamEnabled=1

#Check if the AP to which we are roaming is better than current AP in terms of RSSI.

#Checking is disabled if set to Zero.Otherwise it will use this value as to how better

#the RSSI of the new/roamable AP should be for roaming

RoamRssiDiff=5

# SAP Country code

# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.

# Example

# US Indoor, USI

# Korea Outdoor, KRO

# Japan without optional byte, JP

# France without optional byte, FR

#gAPCntryCode=USI

#Short Guard Interval Enable/disable

gShortGI20Mhz=1

gShortGI40Mhz=1

#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled

gAPAutoShutOff=0

#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec

gWlanAutoShutdown = 0

# SAP auto channel selection configuration

# 0 = disable auto channel selection

# 1 = enable auto channel selection, channel provided by supplicant will be ignored

gApAutoChannelSelection=0

# Listen Energy Detect Mode Configuration

# Valid values 0-128

# 128 means disable Energy Detect feature

# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.

# 10-128 are reserved.

# The EDET threshold mapping is as follows in 3dB step:

# 0 = -60 dBm

# 1 = -63 dBm

# 2 = -66 dBm

# ...

# 7 = -81 dBm

# 8 = -84 dBm

# 9 = -87 dBm

# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:

# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm.

gEnablePhyAgcListenMode=128

#Preferred channel to start BT AMP AP mode (0 means, any channel)

BtAmpPreferredChannel=0

#Preferred band (both or 2.4 only or 5 only)

BandCapability=0

#Beacon Early Termination (1 = enable the BET feature, 0 = disable)

enableBeaconEarlyTermination=1

beaconEarlyTerminationWakeInterval=11

#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)

gEnableBtAmp=0

#SOFTAP Channel Range selection

gAPChannelSelectStartChannel=1

gAPChannelSelectEndChannel=11

#SOFTAP Channel Range selection Operating band

# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND

gAPChannelSelectOperatingBand=0

#Channel Bonding

gChannelBondingMode5GHz=1

gEnableModulatedDTIM = 3

gMaxLIModulatedDTIM = 3

gEnableDatainactivity = 200

#Enable Keep alive with non-zero period value

gStaKeepAlivePeriod=30

#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).

#For every 10 seconds DUT sends Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)

#For both active and power save clients.

#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.

#If doesn't honor for 5 seconds then Driver remove client.

#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still DUT try on

#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.

#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod +gGoLinkMonitorPeriod)..

#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period

#where we send NULL frame.

#gApLinkMonitorPeriod = 10

#gGoLinkMonitorPeriod = 10

#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.

#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.

gGoKeepAlivePeriod = 10

gApKeepAlivePeriod = 30

#If set will start with active scan after driver load, otherwise will start with

#passive scan to find out the domain

#gEnableBypass11d=1

#If set to 0, will not scan DFS channels

gEnableDFSChnlScan=1

gEnableLogp=1

# Enable Automatic Tx Power control

gEnableAutomaticTxPowerControl=0

# 0 for OLPC 1 for CLPC and SCPC

gEnableCloseLoop=1

#Data Inactivity Timeout when in powersave (in ms)

gDataInactivityTimeout=200

gEnableLpwrImgTransition=1

# Scan Timing Parameters

# gPassiveMaxChannelTime=110

# gPassiveMinChannelTime=60

# Enable Tx LDPC

#gTxLdpcEnable = 1 for HT mode, 2 for VHT mode,3 for both HT and VHT

gTxLdpcEnable=3

# gActiveMaxChannelTime=40

# gActiveMinChannelTime=20

# Valid values are 2048,4096,8192 and so on

# Please don't use values other than the ones mentioned above

gMaxMediumTime=4096

# 802.11K support

gRrmEnable=1

gRrmOperChanMax=8

gRrmNonOperChanMax=8

gRrmRandIntvl=100

#Scan offload

gEnableDirectedScanOffload=0

#FlexConnect Power Factor

#Default is set to 0 (disable)

gFlexConnectPowerFactor=0

gVhtChannelWidth=2

# VHT Tx/Rx MCS values

# Valid values are 0,1,2. If commented out, the default value is 0.

# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9

gVhtRxMCS=2

gVhtTxMCS=2

# Enable Tx beamforming

gTxBFEnable=1

#Enable/Disable TDLS Feature

gEnableTDLSSupport=1

#Enable/Disable TDLS Implicit Trigger

gEnableTDLSImplicitTrigger=0

#Enable/Disable TDLS WMM Mode

gEnableTDLSWmmMode=1

#Enable/Disable TDLS Buffer Sta

gEnableTDLSBufferSta=1

#Enable/Disable Mgmt Frame Logging

gEnableMgmtLogging=1

#Enable/Disable MAc Spoofing

gEnableMacAddrSpoof=1

#Set RPS CPU mask

rps_mask=0f

#wuzhiyong wifi bt coexistence

gBtcStaticOppWlanIdleWlanLen=30000

gBtcStaticOppWlanIdleBtLen=120000

#Configures Channel Bonding in 24 GHz

gChannelBondingMode24GHz=1

# Disable rx wakelock

rx_wakelock_timeout=0

# Enable/Disable conversion from SARV1 to SARV2

gEnableSARV1toSARV2=1

# Set sta preference to connect in 80HZ/160HZ

gStaPrefer80MHzOver160MHz=1

# Sets RSSI preference for 5GHz over 2.4GHz AP

#gSelect5GHzMargin=5

# TheCrazyLex@PA Prefer connecting to 5Ghz AP

# even if its RSSI is lower by 3dBm than the 2.4Ghz AP

# gRoamPrefer5GHz=1

# Firmware log mode

# Valid values are 0,1,2

# 0=Disable, 1=WMI, 2=DIAG

gEnablefwlog=0

# Timer waiting for interface up from the upper layer

gInterfaceChangeWait=1000

#Enable Power Save offload

gEnablePowerSaveOffload=4

# 0: Disable BPF packet filter

# 1: Enable BPF packet filter

gBpfFilterEnable=0

# Enable/Disable NUD Tracking within driver

gEnableNUDTracking=0

# Enable broadcast logging to the userspace entities

gMulticastHostFwMsgs=0

# Disable packetlog explicitly

gEnablePacketLog=0

#Skip DFS Channel in case of P2P Search

# 0 - disable (Scan DFS Channel in P2P Search)

# 1 - enable (Skip DFS Channel)

gSkipDfsChannelInP2pSearch=0

END

# Note: Configuration parser would not read anything past the END marker

Saved diffs

Original text

Open file

# This file allows user to override the factory

# defaults for the WLAN Driver

# Enable IMPS or not
gEnableImps=1

# Enable/Disable Idle Scan

gEnableIdleScan=0

# Increase sleep duration (seconds) during IMPS
# 0 implies no periodic wake up from IMPS. Periodic wakeup is
# unnecessary if Idle Scan is disabled.
gImpsModSleepTime=0

# Enable BMPS or not
gEnableBmps=1

# Enable suspend or not

# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter

gEnableSuspend=3

# Phy Mode (auto, b, g, n, etc)
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
gDot11Mode=0

# CSR Roaming Enable(1) Disable(0)

gRoamingTime=0

# Assigned MAC Addresses - This will be used until NV items are in place

# Each byte of MAC address is represented in Hex format as XX

Intf0MacAddress=000AF58989FF
Intf1MacAddress=000AF58989FE
Intf2MacAddress=000AF58989FD

Intf3MacAddress=000AF58989FC

# Set/Clear UAPSD mask

UapsdMask=0

# UAPSD service interval for VO,VI, BE, BK traffic

InfraUapsdVoSrvIntv=20

InfraUapsdViSrvIntv=40

# Flag to allow STA send AddTspec even when ACM is Off
gAddTSWhenACMIsOff=1

# Make 1x1 the default antenna configuration

gNumRxAnt=1

# Beacon filtering frequency (unit in beacon intervals)

gNthBeaconFilter=50

# Enable WAPI or not

# WAPIIsEnabled=0

# Flags to filter Mcast abd Bcast RX packets.

# Value 0: No filtering, 1: Filter all Multicast.

# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast

McastBcastFilter=3

#Flag to enable HostARPOffload feature or not

hostArpOffload=1

#SoftAP Related Parameters

# AP MAc addr

gAPMacAddr=000AF589dcab

# 802.11n Protection flag

gEnableApProt=1

#Enable OBSS protection

gEnableApOBSSProt=1

#Enable/Disable UAPSD for SoftAP

gEnableApUapsd=1

# Fixed Rate

gFixedRate=0

# Maximum Tx power

# gTxPowerCap=30

# Fragmentation Threshold

# gFragmentationThreshold=2346

# RTS threshold

RTSThreshold=2346

# Intra-BSS forward

gDisableIntraBssFwd=0

# WMM Enable/Disable

WmmIsEnabled=0

# 802.11d support

g11dSupportEnabled=0

# CCX Support and fast transition
EseEnabled=0
FastTransitionEnabled=1
ImplicitQosIsEnabled=0
gNeighborScanTimerPeriod=200

# default value of this parameter is zero to enable dynamic threshold allocation
# to set static roming threshold uncomment below parameter and set vaule
#gNeighborLookupThreshold=78

gNeighborScanChannelMinTime=20
gNeighborScanChannelMaxTime=30

# Legacy (non-CCX, non-802.11r) Fast Roaming Support
# To enable, set FastRoamEnabled=1
# To disable, set FastRoamEnabled=0
FastRoamEnabled=1

#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
#the RSSI of the new/roamable AP should be for roaming
RoamRssiDiff=5

# SAP Country code

# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.

# Example

#   US Indoor, USI

#   Korea Outdoor, KRO

#   Japan without optional byte, JP

#   France without optional byte, FR

#gAPCntryCode=USI

#Short Guard Interval Enable/disable

gShortGI20Mhz=1

gShortGI40Mhz=1

#Auto Shutdown  Value in seconds. A value of 0 means Auto shutoff is disabled

gAPAutoShutOff=0

# SAP auto channel selection configuration

# 0 = disable auto channel selection

# 1 = enable auto channel selection, channel provided by supplicant will be ignored

gApAutoChannelSelection=0

# Listen Energy Detect Mode Configuration

# Valid values 0-128

# 128 means disable Energy Detect feature

# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.

# 10-128 are reserved.

# The EDET threshold mapping is as follows in 3dB step:

# 0 = -60 dBm

# 1 = -63 dBm

# 2 = -66 dBm

# ...

# 7 = -81 dBm

# 8 = -84 dBm

# 9 = -87 dBm

# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:

#  Range Loss  (dB)  =  EDET threshold level (dBm) + 97 dBm.

gEnablePhyAgcListenMode=128

#Preferred channel to start BT AMP AP mode (0 means, any channel)

BtAmpPreferredChannel=0

#Preferred band (both or 2.4 only or 5 only)

BandCapability=0

#Beacon Early Termination (1 = enable the BET feature, 0 = disable)

enableBeaconEarlyTermination=1

beaconEarlyTerminationWakeInterval=11

#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)

gEnableBtAmp=0

#SOFTAP Channel Range selection

gAPChannelSelectStartChannel=1

gAPChannelSelectEndChannel=11

#SOFTAP Channel Range selection Operating band

# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND

gAPChannelSelectOperatingBand=0

#Channel Bonding
gChannelBondingMode5GHz=1

gEnableModulatedDTIM = 3
gMaxLIModulatedDTIM = 3
gEnableDatainactivity = 200

#Enable Keep alive with non-zero period value

gStaKeepAlivePeriod=30

#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
#For every 10 seconds DUT sends Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
#For both active and power save clients.

#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
#If doesn't honor for 5 seconds then Driver remove client.

#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still DUT try on
#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod +gGoLinkMonitorPeriod)..

#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
#where we send NULL frame.

#gApLinkMonitorPeriod = 10

#gGoLinkMonitorPeriod = 10

#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
gGoKeepAlivePeriod = 10

gApKeepAlivePeriod = 30
#If set will start with active scan after driver load, otherwise will start with

#passive scan to find out the domain

#gEnableBypass11d=1

#If set to 0, will not scan DFS channels

gEnableDFSChnlScan=1

gEnableLogp=1

# Enable Automatic Tx Power control

gEnableAutomaticTxPowerControl=0

# 0 for OLPC 1 for CLPC and SCPC
gEnableCloseLoop=1

#Data Inactivity Timeout when in powersave (in ms)
gDataInactivityTimeout=200

gEnableLpwrImgTransition=1

# Scan Timing Parameters
# gPassiveMaxChannelTime=110
# gPassiveMinChannelTime=60
# Enable Tx LDPC
#gTxLdpcEnable = 1 for HT mode, 2 for VHT mode,3 for both HT and VHT
gTxLdpcEnable=3
# gActiveMaxChannelTime=40
# gActiveMinChannelTime=20

# Valid values are 2048,4096,8192 and so on
# Please don't use values other than the ones mentioned above
gMaxMediumTime=4096

# 802.11K support
gRrmEnable=1
gRrmOperChanMax=8
gRrmNonOperChanMax=8
gRrmRandIntvl=100

#Scan offload
gEnableDirectedScanOffload=0

#FlexConnect Power Factor
#Default is set to 0 (disable)
gFlexConnectPowerFactor=0

gVhtChannelWidth=2

# VHT Tx/Rx MCS values
# Valid values are 0,1,2. If commented out, the default value is 0.
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
gVhtRxMCS=2
gVhtTxMCS=2

# Enable Tx beamforming
gTxBFEnable=1

#Enable/Disable TDLS Feature
gEnableTDLSSupport=1

#Enable/Disable TDLS Implicit Trigger
gEnableTDLSImplicitTrigger=0

#Enable/Disable TDLS WMM Mode
gEnableTDLSWmmMode=1

#Enable/Disable TDLS Buffer Sta
gEnableTDLSBufferSta=1

#Enable/Disable Mgmt Frame Logging
gEnableMgmtLogging=1

#Enable/Disable MAc Spoofing
gEnableMacAddrSpoof=1

#Set RPS CPU mask
rps_mask=0f

#wuzhiyong wifi bt coexistence
gBtcStaticOppWlanIdleWlanLen=30000
gBtcStaticOppWlanIdleBtLen=120000

END

# Note: Configuration parser would not read anything past the END marker

Changed text

Open file

# This file allows user to override the factory

# defaults for the WLAN Driver

# Enable IMPS or not
gEnableImps=1

# Enable/Disable Idle Scan

gEnableIdleScan=0

# Increase sleep duration (seconds) during IMPS
# 0 implies no periodic wake up from IMPS. Periodic wakeup is
# unnecessary if Idle Scan is disabled.
gImpsModSleepTime=0

# Enable BMPS or not
gEnableBmps=1

# Enable suspend or not

# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter

gEnableSuspend=3

# Phy Mode (auto, b, g, n, etc)
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
gDot11Mode=0

# CSR Roaming Enable(1) Disable(0)

gRoamingTime=0

# Assigned MAC Addresses - This will be used until NV items are in place

# Each byte of MAC address is represented in Hex format as XX

Intf0MacAddress=000AF58989FF
Intf1MacAddress=000AF58989FE
Intf2MacAddress=000AF58989FD

Intf3MacAddress=000AF58989FC

# Set/Clear UAPSD mask

UapsdMask=0

# UAPSD service interval for VO,VI, BE, BK traffic

InfraUapsdVoSrvIntv=0
InfraUapsdViSrvIntv=0
InfraUapsdBeSrvIntv=0
InfraUapsdBkSrvIntv=0

# Flag to allow STA send AddTspec even when ACM is Off
gAddTSWhenACMIsOff=1

# Make 1x1 the default antenna configuration

gNumRxAnt=1

# Beacon filtering frequency (unit in beacon intervals)

gNthBeaconFilter=50

# Enable WAPI or not

# WAPIIsEnabled=0

# Flags to filter Mcast abd Bcast RX packets.

# Value 0: No filtering, 1: Filter all Multicast.

# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast

McastBcastFilter=3

#Flag to enable HostARPOffload feature or not

hostArpOffload=1

#SoftAP Related Parameters

# AP MAc addr

gAPMacAddr=000AF589dcab

# 802.11n Protection flag

gEnableApProt=1

#Enable OBSS protection

gEnableApOBSSProt=1

#Enable/Disable UAPSD for SoftAP

gEnableApUapsd=1

# Fixed Rate

gFixedRate=0

# Maximum Tx power
# gTxPowerCap=4

# Fragmentation Threshold

# gFragmentationThreshold=2346

# RTS threshold

RTSThreshold=1048576

# Intra-BSS forward

gDisableIntraBssFwd=0

# WMM Enable/Disable

WmmIsEnabled=0

# 802.11d support

g11dSupportEnabled=0

# CCX Support and fast transition
EseEnabled=0
FastTransitionEnabled=1
ImplicitQosIsEnabled=0
gNeighborScanTimerPeriod=200

# default value of this parameter is zero to enable dynamic threshold allocation
# to set static roming threshold uncomment below parameter and set vaule
# gNeighborLookupThreshold=85
gNeighborScanChannelMinTime=20
gNeighborScanChannelMaxTime=30
gMaxNeighborReqTries=3

# Legacy (non-CCX, non-802.11r) Fast Roaming Support
# To enable, set FastRoamEnabled=1
# To disable, set FastRoamEnabled=0
FastRoamEnabled=1

# SAP Country code

# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.

# Example

#   US Indoor, USI

#   Korea Outdoor, KRO

#   Japan without optional byte, JP

#   France without optional byte, FR

#gAPCntryCode=USI

#Short Guard Interval Enable/disable
gShortGI20Mhz=1
gShortGI40Mhz=1

#Auto Shutdown  Value in seconds. A value of 0 means Auto shutoff is disabled

gAPAutoShutOff=0

#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec
gWlanAutoShutdown = 0

# SAP auto channel selection configuration

# 0 = disable auto channel selection

# 1 = enable auto channel selection, channel provided by supplicant will be ignored

gApAutoChannelSelection=0

# Listen Energy Detect Mode Configuration

# Valid values 0-128

# 128 means disable Energy Detect feature

# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.

# 10-128 are reserved.

# The EDET threshold mapping is as follows in 3dB step:

# 0 = -60 dBm

# 1 = -63 dBm

# 2 = -66 dBm

# ...

# 7 = -81 dBm

# 8 = -84 dBm

# 9 = -87 dBm

# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:

#  Range Loss  (dB)  =  EDET threshold level (dBm) + 97 dBm.

gEnablePhyAgcListenMode=128

#Preferred channel to start BT AMP AP mode (0 means, any channel)

BtAmpPreferredChannel=0

#Preferred band (both or 2.4 only or 5 only)

BandCapability=0

#Beacon Early Termination (1 = enable the BET feature, 0 = disable)

enableBeaconEarlyTermination=1

beaconEarlyTerminationWakeInterval=11

#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)

gEnableBtAmp=0

#SOFTAP Channel Range selection

gAPChannelSelectStartChannel=1

gAPChannelSelectEndChannel=11

#SOFTAP Channel Range selection Operating band

# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND

gAPChannelSelectOperatingBand=0

#Channel Bonding
gChannelBondingMode5GHz=1

gEnableModulatedDTIM = 3
gMaxLIModulatedDTIM = 3
gEnableDatainactivity = 200

#Enable Keep alive with non-zero period value

gStaKeepAlivePeriod=30

#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
#If doesn't honor for 5 seconds then Driver remove client.

#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
#where we send NULL frame.

#gApLinkMonitorPeriod = 10

#gGoLinkMonitorPeriod = 10

gApKeepAlivePeriod = 30
#If set will start with active scan after driver load, otherwise will start with

#passive scan to find out the domain

#gEnableBypass11d=1

#If set to 0, will not scan DFS channels

gEnableDFSChnlScan=1

gEnableLogp=1

# Enable Automatic Tx Power control

gEnableAutomaticTxPowerControl=0

# 0 for OLPC 1 for CLPC and SCPC
gEnableCloseLoop=1

#Data Inactivity Timeout when in powersave (in ms)
gDataInactivityTimeout=200

gEnableLpwrImgTransition=1

# Valid values are 2048,4096,8192 and so on
# Please don't use values other than the ones mentioned above
gMaxMediumTime=4096

# 802.11K support
gRrmEnable=1
gRrmOperChanMax=8
gRrmNonOperChanMax=8
gRrmRandIntvl=100

#Scan offload
gEnableDirectedScanOffload=0

#FlexConnect Power Factor
#Default is set to 0 (disable)
gFlexConnectPowerFactor=0

gVhtChannelWidth=2

# VHT Tx/Rx MCS values
# Valid values are 0,1,2. If commented out, the default value is 0.
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
gVhtRxMCS=2
gVhtTxMCS=2

# Enable Tx beamforming
gTxBFEnable=1

#Enable/Disable TDLS Feature
gEnableTDLSSupport=1

#Enable/Disable TDLS Implicit Trigger
gEnableTDLSImplicitTrigger=0

#Enable/Disable TDLS WMM Mode
gEnableTDLSWmmMode=1

#Enable/Disable TDLS Buffer Sta
gEnableTDLSBufferSta=1

#Enable/Disable Mgmt Frame Logging
gEnableMgmtLogging=1

#Enable/Disable MAc Spoofing
gEnableMacAddrSpoof=1

#Set RPS CPU mask
rps_mask=0f

#wuzhiyong wifi bt coexistence
gBtcStaticOppWlanIdleWlanLen=30000
gBtcStaticOppWlanIdleBtLen=120000

#Configures Channel Bonding in 24 GHz
gChannelBondingMode24GHz=1

# Disable rx wakelock
rx_wakelock_timeout=0

# Enable/Disable conversion from SARV1 to SARV2
gEnableSARV1toSARV2=1

# Set sta preference to connect in 80HZ/160HZ
gStaPrefer80MHzOver160MHz=1

# Sets RSSI preference for 5GHz over 2.4GHz AP
#gSelect5GHzMargin=5

# TheCrazyLex@PA Prefer connecting to 5Ghz AP
# even if its RSSI is lower by 3dBm than the 2.4Ghz AP
# gRoamPrefer5GHz=1

# Firmware log mode
# Valid values are 0,1,2
# 0=Disable, 1=WMI, 2=DIAG
gEnablefwlog=0

# Timer waiting for interface up from the upper layer
gInterfaceChangeWait=1000

#Enable Power Save offload
gEnablePowerSaveOffload=4

# 0: Disable BPF packet filter
# 1: Enable BPF packet filter
gBpfFilterEnable=0

# Enable/Disable NUD Tracking within driver
gEnableNUDTracking=0

# Enable broadcast logging to the userspace entities
gMulticastHostFwMsgs=0

# Disable packetlog explicitly
gEnablePacketLog=0

#Skip DFS Channel in case of P2P Search
# 0 - disable (Scan DFS Channel in P2P Search)
# 1 - enable (Skip DFS Channel)
gSkipDfsChannelInP2pSearch=0

END

# Note: Configuration parser would not read anything past the END marker