テキスト比較

2 つのテキストファイルの違いを見つける

ライブエディター

空白の変更を非表示

未変更行を折りたたむ

折り返しなし

レイアウト

比較精度

テキストスタイル

シンタックスハイライト

Diffchecker Desktop Diffcheckerを実行する最も安全な方法。Diffchecker Desktopアプリを入手：あなたの差分はコンピューターから出ることはありません！Desktopを入手

Untitled diff

作成日 11 年前差分は期限切れになりません

25 削除

行
合計
削除

文字
合計
削除

この機能を引き続き使用するには、アップグレードしてください Diffchecker Pro 価格を見る

801 行

21 追加

行
合計
追加

文字
合計
追加

この機能を引き続き使用するには、アップグレードしてください Diffchecker Pro 価格を見る

787 行

/**********************************************************/

/* Serial Bootloader for Atmel megaAVR Controllers */

/* */

/* tested with ATmega8, ATmega128 and ATmega168 */

/* should work with other mega's, see code for details */

/* */

/* ATmegaBOOT.c */

/* */

/* 20130613: Added support for ATmega128RFA1 */

/* 20090308: integrated Mega changes into main bootloader */

/* source by D. Mellis */

/* 20080930: hacked for Arduino Mega (with the 1280 */

/* processor, backwards compatible) */

/* by D. Cuartielles */

/* 20070626: hacked for Arduino Diecimila (which auto- */

/* resets when a USB connection is made to it) */

/* by D. Mellis */

/* 20060802: hacked for Arduino by D. Cuartielles */

/* based on a previous hack by D. Mellis */

/* and D. Cuartielles */

/* */

/* Monitor and debug functions were added to the original */

/* code by Dr. Erik Lins, chip45.com. (See below) */

/* */

/* Thanks to Karl Pitrich for fixing a bootloader pin */

/* problem and more informative LED blinking! */

/* */

/* For the latest version see: */

/* http://www.chip45.com/ */

/* */

/* ------------------------------------------------------ */

/* */

/* based on stk500boot.c */

/* see avr1.org for original file and information */

/* */

/* This program is free software; you can redistribute it */

/* and/or modify it under the terms of the GNU General */

/* Public License as published by the Free Software */

/* Foundation; either version 2 of the License, or */

/* (at your option) any later version. */

/* */

/* This program is distributed in the hope that it will */

/* be useful, but WITHOUT ANY WARRANTY; without even the */

/* implied warranty of MERCHANTABILITY or FITNESS FOR A */

/* PARTICULAR PURPOSE. See the GNU General Public */

/* License for more details. */

/* */

/* You should have received a copy of the GNU General */

/* Public License along with this program; if not, write */

/* to the Free Software Foundation, Inc., */

/* 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */

/* */

/* Licence can be viewed at */

/* http://www.fsf.org/licenses/gpl.txt */

/* */

/* Target = Atmel AVR m128,m64,m32,m16,m8,m162,m163,m169, */

/* m8515,m8535. ATmega161 has a very small boot block so */

/* isn't supported. */

/* */

/* Tested with m168 */

/**********************************************************/

/* $Id$ */

/* some includes */

#include <inttypes.h>

#include <avr/io.h>

#include <avr/pgmspace.h>

#include <avr/interrupt.h>

#include <avr/wdt.h>

#include <util/delay.h>

/* the current avr-libc eeprom functions do not support the ATmega168 */

/* own eeprom write/read functions are used instead */

#if !defined(__AVR_ATmega168__) || !defined(__AVR_ATmega328P__)

#include <avr/eeprom.h>

#endif

/* Use the F_CPU defined in Makefile */

/* 20060803: hacked by DojoCorp */

/* 20070626: hacked by David A. Mellis to decrease waiting time for auto-reset */

/* set the waiting time for the bootloader */

/* get this from the Makefile instead */

/* #define MAX_TIME_COUNT (F_CPU>>4) */

/* 20070707: hacked by David A. Mellis - after this many errors give up and launch application */

#define MAX_ERROR_COUNT 5

/* set the UART baud rate */

/* 20060803: hacked by DojoCorp */

//#define BAUD_RATE 115200

#ifndef BAUD_RATE

#define BAUD_RATE 19200

#endif

/* SW_MAJOR and MINOR needs to be updated from time to time to avoid warning message from AVR Studio */

/* never allow AVR Studio to do an update !!!! */

#define HW_VER 0x02

#define SW_MAJOR 0x01

#define SW_MINOR 0x10

/* Adjust to suit whatever pin your hardware uses to enter the bootloader */

/* ATmega128 has two UARTS so two pins are used to enter bootloader and select UART */

/* ATmega1280 has four UARTS, but for Arduino Mega, we will only use RXD0 to get code */

/* BL0... means UART0, BL1... means UART1 */

#ifdef __AVR_ATmega128__

#define BL_DDR DDRF

#define BL_PORT PORTF

#define BL_PIN PINF

#define BL0 PINF7

#define BL1 PINF6

/*#elif defined __AVR_ATmega128RFA1__*/

/* ToDO Enable bootloading via both UARTs */

#elif defined __AVR_ATmega1280__

/* we just don't do anything for the MEGA and enter bootloader on reset anyway*/

#else

/* other ATmegas have only one UART, so only one pin is defined to enter bootloader */

#define BL_DDR DDRD

#define BL_PORT PORTD

#define BL_PIN PIND

#define BL PIND6

#endif

/* onboard LED is used to indicate, that the bootloader was entered (3x flashing) */

/* if monitor functions are included, LED goes on after monitor was entered */

#if defined __AVR_ATmega128__ || defined __AVR_ATmega1280__

#if defined __AVR_ATmega128__ || defined __AVR_ATmega1280__ || defined __AVR_ATmega128RFA1__

/* Onboard LED is connected to pin PB7 (e.g. Crumb128, PROBOmega128, Savvy128, Arduino Mega) */

#define LED_DDR DDRB

#define LED_PORT PORTB

#define LED_PIN PINB

#define LED PINB7

#else

/* Onboard LED is connected to pin PB5 in Arduino NG, Diecimila, and Duomilanuove */

/* other boards like e.g. Crumb8, Crumb168 are using PB2 */

#define LED_DDR DDRB

#define LED_PORT PORTB

#define LED_PIN PINB

#define LED PINB5

#endif

/* monitor functions will only be compiled when using ATmega128, due to bootblock size constraints */

#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)

#define MONITOR 1

#endif

/* define various device id's */

/* manufacturer byte is always the same */

#define SIG1 0x1E // Yep, Atmel is the only manufacturer of AVR micros. Single source :(

#if defined __AVR_ATmega1280__

#define SIG2 0x97

#define SIG3 0x03

#define PAGE_SIZE 0x80U //128 words

#elif defined __AVR_ATmega1281__

#define SIG2 0x97

#define SIG3 0x04

#define PAGE_SIZE 0x80U //128 words

#elif defined __AVR_ATmega128__

#define SIG2 0x97

#define SIG3 0x02

#define PAGE_SIZE 0x80U //128 words

#elif defined __AVR_ATmega128RFA1__

#define SIG2 0xA7

#define SIG3 0x01

#define PAGE_SIZE 0x80U // 128 words

#elif defined __AVR_ATmega64__

#define SIG2 0x96

#define SIG3 0x02

#define PAGE_SIZE 0x80U //128 words

#elif defined __AVR_ATmega32__

#define SIG2 0x95

#define SIG3 0x02

#define PAGE_SIZE 0x40U //64 words

#elif defined __AVR_ATmega16__

#define SIG2 0x94

#define SIG3 0x03

#define PAGE_SIZE 0x40U //64 words

#elif defined __AVR_ATmega8__

#define SIG2 0x93

#define SIG3 0x07

#define PAGE_SIZE 0x20U //32 words

#elif defined __AVR_ATmega88__

#define SIG2 0x93

#define SIG3 0x0a

#define PAGE_SIZE 0x20U //32 words

#elif defined __AVR_ATmega168__

#define SIG2 0x94

#define SIG3 0x06

#define PAGE_SIZE 0x40U //64 words

#elif defined __AVR_ATmega328P__

#define SIG2 0x95

#define SIG3 0x0F

#define PAGE_SIZE 0x40U //64 words

#elif defined __AVR_ATmega162__

#define SIG2 0x94

#define SIG3 0x04

#define PAGE_SIZE 0x40U //64 words

#elif defined __AVR_ATmega163__

#define SIG2 0x94

#define SIG3 0x02

#define PAGE_SIZE 0x40U //64 words

#elif defined __AVR_ATmega169__

#define SIG2 0x94

#define SIG3 0x05

#define PAGE_SIZE 0x40U //64 words

#elif defined __AVR_ATmega8515__

#define SIG2 0x93

#define SIG3 0x06

#define PAGE_SIZE 0x20U //32 words

#elif defined __AVR_ATmega8535__

#define SIG2 0x93

#define SIG3 0x08

#define PAGE_SIZE 0x20U //32 words

#endif

/* function prototypes */

void putch(char);

char getch(void);

void getNch(uint8_t);

void byte_response(uint8_t);

void nothing_response(void);

char gethex(void);

void puthex(char);

void flash_led(uint8_t);

/* some variables */

union address_union {

uint16_t word;

uint8_t byte[2];

} address;

union length_union {

uint16_t word;

uint8_t byte[2];

} length;

struct flags_struct {

unsigned eeprom : 1;

unsigned rampz : 1;

} flags;

uint8_t buff[256];

uint8_t address_high;

uint8_t pagesz=0x80;

uint8_t i;

uint8_t bootuart = 0;

uint8_t error_count = 0;

void (*app_start)(void) = 0x0000;

/* main program starts here */

int main(void)

{

uint8_t ch,ch2;

uint16_t w;

#ifdef WATCHDOG_MODS

ch = MCUSR;

MCUSR = 0;

WDTCSR |= _BV(WDCE) | _BV(WDE);

WDTCSR = 0;

// Check if the WDT was used to reset, in which case we dont bootload and skip straight to the code. woot.

if (! (ch & _BV(EXTRF))) // if its a not an external reset...

app_start(); // skip bootloader

#else

asm volatile("nop\n\t");

#endif

/* set pin direction for bootloader pin and enable pullup */

/* for ATmega128, two pins need to be initialized */

#ifdef __AVR_ATmega128__

BL_DDR &= ~_BV(BL0);

BL_DDR &= ~_BV(BL1);

BL_PORT |= _BV(BL0);

BL_PORT |= _BV(BL1);

#else

/* We run the bootloader regardless of the state of this pin. Thus, don't

put it in a different state than the other pins. --DAM, 070709

This also applies to Arduino Mega -- DC, 080930

BL_DDR &= ~_BV(BL);

BL_PORT |= _BV(BL);

#endif

#ifdef __AVR_ATmega128__

/* check which UART should be used for booting */

if(bit_is_clear(BL_PIN, BL0)) {

bootuart = 1;

}

else if(bit_is_clear(BL_PIN, BL1)) {

bootuart = 2;

}

#endif

#if defined __AVR_ATmega1280__

#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega128RFA1__)

/* the mega1280 chip has four serial ports ... we could eventually use any of them, or not? */

/* however, we don't wanna confuse people, to avoid making a mess, we will stick to RXD0, TXD0 */

bootuart = 1;

#endif

/* check if flash is programmed already, if not start bootloader anyway */

if(pgm_read_byte_near(0x0000) != 0xFF) {

#ifdef __AVR_ATmega128__

/* no UART was selected, start application */

if(!bootuart) {

app_start();

}

#else

/* check if bootloader pin is set low */

/* we don't start this part neither for the m8, nor m168 */

//if(bit_is_set(BL_PIN, BL)) {

// app_start();

// }

#endif

}

#ifdef __AVR_ATmega128__

/* no bootuart was selected, default to uart 0 */

if(!bootuart) {

bootuart = 1;

}

#endif

/* initialize UART(s) depending on CPU defined */

#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)

#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__) || defined(__AVR_ATmega128RFA1__)

if(bootuart == 1) {

UBRR0L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);

UBRR0H = (F_CPU/(BAUD_RATE*16L)-1) >> 8;

UCSR0A = 0x00;

UCSR0C = 0x06;

UCSR0B = _BV(TXEN0)|_BV(RXEN0);

}

if(bootuart == 2) {

UBRR1L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);

UBRR1H = (F_CPU/(BAUD_RATE*16L)-1) >> 8;

UCSR1A = 0x00;

UCSR1C = 0x06;

UCSR1B = _BV(TXEN1)|_BV(RXEN1);

}

#elif defined __AVR_ATmega163__

UBRR = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);

UBRRHI = (F_CPU/(BAUD_RATE*16L)-1) >> 8;

UCSRA = 0x00;

UCSRB = _BV(TXEN)|_BV(RXEN);

#elif defined(__AVR_ATmega168__) || defined(__AVR_ATmega328P__)

#ifdef DOUBLE_SPEED

UCSR0A = (1<<U2X0); //Double speed mode USART0

UBRR0L = (uint8_t)(F_CPU/(BAUD_RATE*8L)-1);

UBRR0H = (F_CPU/(BAUD_RATE*8L)-1) >> 8;

#else

UBRR0L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);

UBRR0H = (F_CPU/(BAUD_RATE*16L)-1) >> 8;

#endif

UCSR0B = (1<<RXEN0) | (1<<TXEN0);

UCSR0C = (1<<UCSZ00) | (1<<UCSZ01);

/* Enable internal pull-up resistor on pin D0 (RX), in order

to supress line noise that prevents the bootloader from

timing out (DAM: 20070509) */

DDRD &= ~_BV(PIND0);

PORTD |= _BV(PIND0);

#elif defined __AVR_ATmega8__

/* m8 */

UBRRH = (((F_CPU/BAUD_RATE)/16)-1)>>8; // set baud rate

UBRRL = (((F_CPU/BAUD_RATE)/16)-1);

UCSRB = (1<<RXEN)|(1<<TXEN); // enable Rx & Tx

UCSRC = (1<<URSEL)|(1<<UCSZ1)|(1<<UCSZ0); // config USART; 8N1

#else

/* m16,m32,m169,m8515,m8535 */

UBRRL = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);

UBRRH = (F_CPU/(BAUD_RATE*16L)-1) >> 8;

UCSRA = 0x00;

UCSRC = 0x06;

UCSRB = _BV(TXEN)|_BV(RXEN);

#endif

#if defined __AVR_ATmega1280__

#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega128RFA1__)

/* Enable internal pull-up resistor on pin D0 (RX), in order

to supress line noise that prevents the bootloader from

timing out (DAM: 20070509) */

/* feature added to the Arduino Mega --DC: 080930 */

DDRE &= ~_BV(PINE0);

PORTE |= _BV(PINE0);

#endif

/* set LED pin as output */

LED_DDR |= _BV(LED);

/* flash onboard LED to signal entering of bootloader */

#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)

#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__) || defined(__AVR_ATmega128RFA1__)

// 4x for UART0, 5x for UART1

flash_led(NUM_LED_FLASHES + bootuart);

#else

flash_led(NUM_LED_FLASHES);

#endif

/* 20050803: by DojoCorp, this is one of the parts provoking the

system to stop listening, cancelled from the original */

//putch('\0');

/* forever loop */

for (;;) {

/* get character from UART */

ch = getch();

/* A bunch of if...else if... gives smaller code than switch...case ! */

/* Hello is anyone home ? */

if(ch=='0') {

nothing_response();

}

/* Request programmer ID */

/* Not using PROGMEM string due to boot block in m128 being beyond 64kB boundry */

/* Would need to selectively manipulate RAMPZ, and it's only 9 characters anyway so who cares. */

else if(ch=='1') {

if (getch() == ' ') {

putch(0x14);

putch('A');

putch('V');

putch('R');

putch(' ');

putch('I');

putch('S');

putch('P');

putch(0x10);

} else {

if (++error_count == MAX_ERROR_COUNT)

app_start();

}

/* AVR ISP/STK500 board commands DON'T CARE so default nothing_response */

else if(ch=='@') {

ch2 = getch();

if (ch2>0x85) getch();

nothing_response();

}

/* AVR ISP/STK500 board requests */

else if(ch=='A') {

ch2 = getch();

if(ch2==0x80) byte_response(HW_VER); // Hardware version

else if(ch2==0x81) byte_response(SW_MAJOR); // Software major version

else if(ch2==0x82) byte_response(SW_MINOR); // Software minor version

else if(ch2==0x98) byte_response(0x03); // Unknown but seems to be required by avr studio 3.56

else byte_response(0x00); // Covers various unnecessary responses we don't care about

}

/* Device Parameters DON'T CARE, DEVICE IS FIXED */

else if(ch=='B') {

getNch(20);

nothing_response();

}

/* Parallel programming stuff DON'T CARE */

else if(ch=='E') {

getNch(5);

nothing_response();

}

/* P: Enter programming mode */

/* R: Erase device, don't care as we will erase one page at a time anyway. */

else if(ch=='P' || ch=='R') {

nothing_response();

}

/* Leave programming mode */

else if(ch=='Q') {

nothing_response();

#ifdef WATCHDOG_MODS

// autoreset via watchdog (sneaky!)

WDTCSR = _BV(WDE);

while (1); // 16 ms

#endif

}

/* Set address, little endian. EEPROM in bytes, FLASH in words */

/* Perhaps extra address bytes may be added in future to support > 128kB FLASH. */

/* This might explain why little endian was used here, big endian used everywhere else. */

else if(ch=='U') {

address.byte[0] = getch();

address.byte[1] = getch();

nothing_response();

}

/* Universal SPI programming command, disabled. Would be used for fuses and lock bits. */

else if(ch=='V') {

if (getch() == 0x30) {

getch();

ch = getch();

getch();

if (ch == 0) {

byte_response(SIG1);

} else if (ch == 1) {

byte_response(SIG2);

} else {

byte_response(SIG3);

}

} else {

getNch(3);

byte_response(0x00);

}

/* Write memory, length is big endian and is in bytes */

else if(ch=='d') {

length.byte[1] = getch();

length.byte[0] = getch();

flags.eeprom = 0;

if (getch() == 'E') flags.eeprom = 1;

for (w=0;w<length.word;w++) {

buff[w] = getch(); // Store data in buffer, can't keep up with serial data stream whilst programming pages

}

if (getch() == ' ') {

if (flags.eeprom) { //Write to EEPROM one byte at a time

address.word <<= 1;

for(w=0;w<length.word;w++) {

#if defined(__AVR_ATmega168__) || defined(__AVR_ATmega328P__)

while(EECR & (1<<EEPE));

EEAR = (uint16_t)(void *)address.word;

EEDR = buff[w];

EECR |= (1<<EEMPE);

EECR |= (1<<EEPE);

#else

eeprom_write_byte((void *)address.word,buff[w]);

#endif

address.word++;

}

else { //Write to FLASH one page at a time

if (address.byte[1]>127) address_high = 0x01; //Only possible with m128, m256 will need 3rd address byte. FIXME

else address_high = 0x00;

#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__) || defined(__AVR_ATmega1281__)

#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__) || defined(__AVR_ATmega1281__) || defined(__AVR_ATmega128RFA1__)

RAMPZ = address_high;

#endif

address.word = address.word << 1; //address * 2 -> byte location

/* if ((length.byte[0] & 0x01) == 0x01) length.word++; //Even up an odd number of bytes */

if ((length.byte[0] & 0x01)) length.word++; //Even up an odd number of bytes

cli(); //Disable interrupts, just to be sure

#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega1281__)

#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega1281__) || defined(__AVR_ATmega128RFA1__)

while(bit_is_set(EECR,EEPE)); //Wait for previous EEPROM writes to complete

#else

while(bit_is_set(EECR,EEWE)); //Wait for previous EEPROM writes to complete

#endif

asm volatile(

"clr r17 \n\t" //page_word_count

"lds r30,address \n\t" //Address of FLASH location (in bytes)

"lds r31,address+1 \n\t"

"ldi r28,lo8(buff) \n\t" //Start of buffer array in RAM

"ldi r29,hi8(buff) \n\t"

"lds r24,length \n\t" //Length of data to be written (in bytes)

"lds r25,length+1 \n\t"

"length_loop: \n\t" //Main loop, repeat for number of words in block

"cpi r17,0x00 \n\t" //If page_word_count=0 then erase page

"brne no_page_erase \n\t"

"wait_spm1: \n\t"

"lds r16,%0 \n\t" //Wait for previous spm to complete

"andi r16,1 \n\t"

"cpi r16,1 \n\t"

"breq wait_spm1 \n\t"

"ldi r16,0x03 \n\t" //Erase page pointed to by Z

"sts %0,r16 \n\t"

"spm \n\t"

#ifdef __AVR_ATmega163__

".word 0xFFFF \n\t"

"nop \n\t"

#endif

"wait_spm2: \n\t"

"lds r16,%0 \n\t" //Wait for previous spm to complete

"andi r16,1 \n\t"

"cpi r16,1 \n\t"

"breq wait_spm2 \n\t"

"ldi r16,0x11 \n\t" //Re-enable RWW section

"sts %0,r16 \n\t"

"spm \n\t"

#ifdef __AVR_ATmega163__

".word 0xFFFF \n\t"

"nop \n\t"

#endif

"no_page_erase: \n\t"

"ld r0,Y+ \n\t" //Write 2 bytes into page buffer

"ld r1,Y+ \n\t"

"wait_spm3: \n\t"

"lds r16,%0 \n\t" //Wait for previous spm to complete

"andi r16,1 \n\t"

"cpi r16,1 \n\t"

"breq wait_spm3 \n\t"

"ldi r16,0x01 \n\t" //Load r0,r1 into FLASH page buffer

"sts %0,r16 \n\t"

"spm \n\t"

"inc r17 \n\t" //page_word_count++

"cpi r17,%1 \n\t"

"brlo same_page \n\t" //Still same page in FLASH

"write_page: \n\t"

"clr r17 \n\t" //New page, write current one first

"wait_spm4: \n\t"

"lds r16,%0 \n\t" //Wait for previous spm to complete

"andi r16,1 \n\t"

"cpi r16,1 \n\t"

"breq wait_spm4 \n\t"

#ifdef __AVR_ATmega163__

"andi r30,0x80 \n\t" // m163 requires Z6:Z1 to be zero during page write

#endif

"ldi r16,0x05 \n\t" //Write page pointed to by Z

"sts %0,r16 \n\t"

"spm \n\t"

#ifdef __AVR_ATmega163__

".word 0xFFFF \n\t"

"nop \n\t"

"ori r30,0x7E \n\t" // recover Z6:Z1 state after page write (had to be zero during write)

#endif

"wait_spm5: \n\t"

"lds r16,%0 \n\t" //Wait for previous spm to complete

"andi r16,1 \n\t"

"cpi r16,1 \n\t"

"breq wait_spm5 \n\t"

"ldi r16,0x11 \n\t" //Re-enable RWW section

"sts %0,r16 \n\t"

"spm \n\t"

#ifdef __AVR_ATmega163__

".word 0xFFFF \n\t"

"nop \n\t"

#endif

"same_page: \n\t"

"adiw r30,2 \n\t" //Next word in FLASH

"sbiw r24,2 \n\t" //length-2

"breq final_write \n\t" //Finished

"rjmp length_loop \n\t"

"final_write: \n\t"

"cpi r17,0 \n\t"

"breq block_done \n\t"

"adiw r24,2 \n\t" //length+2, fool above check on length after short page write

"rjmp write_page \n\t"

"block_done: \n\t"

"clr __zero_reg__ \n\t" //restore zero register

#if defined __AVR_ATmega168__ || __AVR_ATmega328P__ || __AVR_ATmega128__ || __AVR_ATmega1280__ || __AVR_ATmega1281__

#if defined __AVR_ATmega168__ || __AVR_ATmega328P__ || __AVR_ATmega128__ || __AVR_ATmega1280__ || __AVR_ATmega1281__ || __AVR_ATmega128RFA1__

: "=m" (SPMCSR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31"

#else

: "=m" (SPMCR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31"

#endif

);

/* Should really add a wait for RWW section to be enabled, don't actually need it since we never */

/* exit the bootloader without a power cycle anyhow */

}

putch(0x14);

putch(0x10);

} else {

if (++error_count == MAX_ERROR_COUNT)

app_start();

}

/* Read memory block mode, length is big endian. */

else if(ch=='t') {

length.byte[1] = getch();

length.byte[0] = getch();

#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)

#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__) || defined(__AVR_ATmega128RFA1__)

if (address.word>0x7FFF) flags.rampz = 1; // No go with m256, FIXME

else flags.rampz = 0;

#endif

address.word = address.word << 1; // address * 2 -> byte location

if (getch() == 'E') flags.eeprom = 1;

else flags.eeprom = 0;

if (getch() == ' ') { // Command terminator

putch(0x14);

for (w=0;w < length.word;w++) { // Can handle odd and even lengths okay

if (flags.eeprom) { // Byte access EEPROM read

#if defined(__AVR_ATmega168__) || defined(__AVR_ATmega328P__)

while(EECR & (1<<EEPE));

EEAR = (uint16_t)(void *)address.word;

EECR |= (1<<EERE);

putch(EEDR);

#else

putch(eeprom_read_byte((void *)address.word));

#endif

address.word++;

}

else {

if (!flags.rampz) putch(pgm_read_byte_near(address.word));

#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)

#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__) || defined(__AVR_ATmega128RFA1__)

else putch(pgm_read_byte_far(address.word + 0x10000));

// Hmmmm, yuck FIXME when m256 arrvies

#endif

address.word++;

}

putch(0x10);

}

/* Get device signature bytes */

else if(ch=='u') {

if (getch() == ' ') {

putch(0x14);

putch(SIG1);

putch(SIG2);

putch(SIG3);

putch(0x10);

} else {

if (++error_count == MAX_ERROR_COUNT)

app_start();

}

/* Read oscillator calibration byte */

else if(ch=='v') {

byte_response(0x00);

}

#if defined MONITOR

/* here come the extended monitor commands by Erik Lins */

/* check for three times exclamation mark pressed */

else if(ch=='!') {

ch = getch();

if(ch=='!') {

ch = getch();

if(ch=='!') {

PGM_P welcome = "";

#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)

#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__) || defined(__AVR_ATmega128RFA1__)

uint16_t extaddr;

#endif

uint8_t addrl, addrh;

#ifdef CRUMB128

welcome = "ATmegaBOOT / Crumb128 - (C) J.P.Kyle, E.Lins - 050815\n\r";

#elif defined PROBOMEGA128

welcome = "ATmegaBOOT / PROBOmega128 - (C) J.P.Kyle, E.Lins - 050815\n\r";

welcome = "ATmegaBOOT / PROBOmega128 - (C)

#elif defined SAVVY128

welcome = "ATmegaBOOT / Savvy128 - (C) J.P.Kyle, E.Lins - 050815\n\r";

#elif defined __AVR_ATmega1280__

welcome = "ATmegaBOOT / Arduino Mega - (C) Arduino LLC - 090930\n\r";

#endif

/* turn on LED */

LED_DDR |= _BV(LED);

LED_PORT &= ~_BV(LED);

/* print a welcome message and command overview */

for(i=0; welcome[i] != '\0'; ++i) {

putch(welcome[i]);

}

/* test for valid commands */

for(;;) {

putch('\n');

putch('\r');

putch(':');

putch('

保存された差分

原文

ファイルを開く

/**********************************************************/
/* Serial Bootloader for Atmel megaAVR Controllers        */
/*                                                        */
/* tested with ATmega8, ATmega128 and ATmega168           */
/* should work with other mega's, see code for details    */
/*                                                        */
/* ATmegaBOOT.c                                           */
/*                                                        */
/*                                                        */
/* 20090308: integrated Mega changes into main bootloader */
/*           source by D. Mellis                          */
/* 20080930: hacked for Arduino Mega (with the 1280       */
/*           processor, backwards compatible)             */
/*           by D. Cuartielles                            */
/* 20070626: hacked for Arduino Diecimila (which auto-    */
/*           resets when a USB connection is made to it)  */
/*           by D. Mellis                                 */
/* 20060802: hacked for Arduino by D. Cuartielles         */
/*           based on a previous hack by D. Mellis        */
/*           and D. Cuartielles                           */
/*                                                        */
/* Monitor and debug functions were added to the original */
/* code by Dr. Erik Lins, chip45.com. (See below)         */
/*                                                        */
/* Thanks to Karl Pitrich for fixing a bootloader pin     */
/* problem and more informative LED blinking!             */
/*                                                        */
/* For the latest version see:                            */
/* http://www.chip45.com/                                 */
/*                                                        */
/* ------------------------------------------------------ */
/*                                                        */
/* based on stk500boot.c                                  */
/* Copyright (c) 2003, Jason P. Kyle                      */
/* All rights reserved.                                   */
/* see avr1.org for original file and information         */
/*                                                        */
/* This program is free software; you can redistribute it */
/* and/or modify it under the terms of the GNU General    */
/* Public License as published by the Free Software       */
/* Foundation; either version 2 of the License, or        */
/* (at your option) any later version.                    */
/*                                                        */
/* This program is distributed in the hope that it will   */
/* be useful, but WITHOUT ANY WARRANTY; without even the  */
/* implied warranty of MERCHANTABILITY or FITNESS FOR A   */
/* PARTICULAR PURPOSE.  See the GNU General Public        */
/* License for more details.                              */
/*                                                        */
/* You should have received a copy of the GNU General     */
/* Public License along with this program; if not, write  */
/* to the Free Software Foundation, Inc.,                 */
/* 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA */
/*                                                        */
/* Licence can be viewed at                               */
/* http://www.fsf.org/licenses/gpl.txt                    */
/*                                                        */
/* Target = Atmel AVR m128,m64,m32,m16,m8,m162,m163,m169, */
/* m8515,m8535. ATmega161 has a very small boot block so  */
/* isn't supported.                                       */
/*                                                        */
/* Tested with m168                                       */
/**********************************************************/

/* $Id$ */

/* some includes */
#include <inttypes.h>
#include <avr/io.h>
#include <avr/pgmspace.h>
#include <avr/interrupt.h>
#include <avr/wdt.h>
#include <util/delay.h>

/* the current avr-libc eeprom functions do not support the ATmega168 */
/* own eeprom write/read functions are used instead */
#if !defined(__AVR_ATmega168__) || !defined(__AVR_ATmega328P__)
#include <avr/eeprom.h>
#endif

/* Use the F_CPU defined in Makefile */

/* 20060803: hacked by DojoCorp */
/* 20070626: hacked by David A. Mellis to decrease waiting time for auto-reset */
/* set the waiting time for the bootloader */
/* get this from the Makefile instead */
/* #define MAX_TIME_COUNT (F_CPU>>4) */

/* 20070707: hacked by David A. Mellis - after this many errors give up and launch application */
#define MAX_ERROR_COUNT 5

/* set the UART baud rate */
/* 20060803: hacked by DojoCorp */
//#define BAUD_RATE   115200
#ifndef BAUD_RATE
#define BAUD_RATE   19200
#endif

/* SW_MAJOR and MINOR needs to be updated from time to time to avoid warning message from AVR Studio */
/* never allow AVR Studio to do an update !!!! */
#define HW_VER	 0x02
#define SW_MAJOR 0x01
#define SW_MINOR 0x10

/* Adjust to suit whatever pin your hardware uses to enter the bootloader */
/* ATmega128 has two UARTS so two pins are used to enter bootloader and select UART */
/* ATmega1280 has four UARTS, but for Arduino Mega, we will only use RXD0 to get code */
/* BL0... means UART0, BL1... means UART1 */
#ifdef __AVR_ATmega128__
#define BL_DDR  DDRF
#define BL_PORT PORTF
#define BL_PIN  PINF
#define BL0     PINF7
#define BL1     PINF6
#elif defined __AVR_ATmega1280__ 
/* we just don't do anything for the MEGA and enter bootloader on reset anyway*/
#else
/* other ATmegas have only one UART, so only one pin is defined to enter bootloader */
#define BL_DDR  DDRD
#define BL_PORT PORTD
#define BL_PIN  PIND
#define BL      PIND6
#endif

/* onboard LED is used to indicate, that the bootloader was entered (3x flashing) */
/* if monitor functions are included, LED goes on after monitor was entered */
#if defined __AVR_ATmega128__ || defined __AVR_ATmega1280__
/* Onboard LED is connected to pin PB7 (e.g. Crumb128, PROBOmega128, Savvy128, Arduino Mega) */
#define LED_DDR  DDRB
#define LED_PORT PORTB
#define LED_PIN  PINB
#define LED      PINB7
#else
/* Onboard LED is connected to pin PB5 in Arduino NG, Diecimila, and Duomilanuove */ 
/* other boards like e.g. Crumb8, Crumb168 are using PB2 */
#define LED_DDR  DDRB
#define LED_PORT PORTB
#define LED_PIN  PINB
#define LED      PINB5
#endif

/* monitor functions will only be compiled when using ATmega128, due to bootblock size constraints */
#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
#define MONITOR 1
#endif

/* define various device id's */
/* manufacturer byte is always the same */
#define SIG1	0x1E	// Yep, Atmel is the only manufacturer of AVR micros.  Single source :(

#if defined __AVR_ATmega1280__
#define SIG2	0x97
#define SIG3	0x03
#define PAGE_SIZE	0x80U	//128 words

#elif defined __AVR_ATmega1281__
#define SIG2	0x97
#define SIG3	0x04
#define PAGE_SIZE	0x80U	//128 words

#elif defined __AVR_ATmega128__
#define SIG2	0x97
#define SIG3	0x02
#define PAGE_SIZE	0x80U	//128 words

#elif defined __AVR_ATmega64__
#define SIG2	0x96
#define SIG3	0x02
#define PAGE_SIZE	0x80U	//128 words

#elif defined __AVR_ATmega32__
#define SIG2	0x95
#define SIG3	0x02
#define PAGE_SIZE	0x40U	//64 words

#elif defined __AVR_ATmega16__
#define SIG2	0x94
#define SIG3	0x03
#define PAGE_SIZE	0x40U	//64 words

#elif defined __AVR_ATmega8__
#define SIG2	0x93
#define SIG3	0x07
#define PAGE_SIZE	0x20U	//32 words

#elif defined __AVR_ATmega88__
#define SIG2	0x93
#define SIG3	0x0a
#define PAGE_SIZE	0x20U	//32 words

#elif defined __AVR_ATmega168__
#define SIG2	0x94
#define SIG3	0x06
#define PAGE_SIZE	0x40U	//64 words

#elif defined __AVR_ATmega328P__
#define SIG2	0x95
#define SIG3	0x0F
#define PAGE_SIZE	0x40U	//64 words

#elif defined __AVR_ATmega162__
#define SIG2	0x94
#define SIG3	0x04
#define PAGE_SIZE	0x40U	//64 words

#elif defined __AVR_ATmega163__
#define SIG2	0x94
#define SIG3	0x02
#define PAGE_SIZE	0x40U	//64 words

#elif defined __AVR_ATmega169__
#define SIG2	0x94
#define SIG3	0x05
#define PAGE_SIZE	0x40U	//64 words

#elif defined __AVR_ATmega8515__
#define SIG2	0x93
#define SIG3	0x06
#define PAGE_SIZE	0x20U	//32 words

#elif defined __AVR_ATmega8535__
#define SIG2	0x93
#define SIG3	0x08
#define PAGE_SIZE	0x20U	//32 words
#endif

/* function prototypes */
void putch(char);
char getch(void);
void getNch(uint8_t);
void byte_response(uint8_t);
void nothing_response(void);
char gethex(void);
void puthex(char);
void flash_led(uint8_t);

/* some variables */
union address_union {
	uint16_t word;
	uint8_t  byte[2];
} address;

union length_union {
	uint16_t word;
	uint8_t  byte[2];
} length;

struct flags_struct {
	unsigned eeprom : 1;
	unsigned rampz  : 1;
} flags;

uint8_t buff[256];
uint8_t address_high;

uint8_t pagesz=0x80;

uint8_t i;
uint8_t bootuart = 0;

uint8_t error_count = 0;

void (*app_start)(void) = 0x0000;

/* main program starts here */
int main(void)
{
	uint8_t ch,ch2;
	uint16_t w;

#ifdef WATCHDOG_MODS
	ch = MCUSR;
	MCUSR = 0;

WDTCSR |= _BV(WDCE) | _BV(WDE);
	WDTCSR = 0;

// Check if the WDT was used to reset, in which case we dont bootload and skip straight to the code. woot.
	if (! (ch &  _BV(EXTRF))) // if its a not an external reset...
		app_start();  // skip bootloader
#else
	asm volatile("nop\n\t");
#endif

/* set pin direction for bootloader pin and enable pullup */
	/* for ATmega128, two pins need to be initialized */
#ifdef __AVR_ATmega128__
	BL_DDR &= ~_BV(BL0);
	BL_DDR &= ~_BV(BL1);
	BL_PORT |= _BV(BL0);
	BL_PORT |= _BV(BL1);
#else
	/* We run the bootloader regardless of the state of this pin.  Thus, don't
	put it in a different state than the other pins.  --DAM, 070709
	This also applies to Arduino Mega -- DC, 080930
	BL_DDR &= ~_BV(BL);
	BL_PORT |= _BV(BL);
	*/
#endif

#ifdef __AVR_ATmega128__
	/* check which UART should be used for booting */
	if(bit_is_clear(BL_PIN, BL0)) {
		bootuart = 1;
	}
	else if(bit_is_clear(BL_PIN, BL1)) {
		bootuart = 2;
	}
#endif

#if defined __AVR_ATmega1280__
	/* the mega1280 chip has four serial ports ... we could eventually use any of them, or not? */
	/* however, we don't wanna confuse people, to avoid making a mess, we will stick to RXD0, TXD0 */
	bootuart = 1;
#endif

/* check if flash is programmed already, if not start bootloader anyway */
	if(pgm_read_byte_near(0x0000) != 0xFF) {

#ifdef __AVR_ATmega128__
	/* no UART was selected, start application */
	if(!bootuart) {
		app_start();
	}
#else
	/* check if bootloader pin is set low */
	/* we don't start this part neither for the m8, nor m168 */
	//if(bit_is_set(BL_PIN, BL)) {
	//      app_start();
	//    }
#endif
	}

#ifdef __AVR_ATmega128__    
	/* no bootuart was selected, default to uart 0 */
	if(!bootuart) {
		bootuart = 1;
	}
#endif

/* initialize UART(s) depending on CPU defined */
#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
	if(bootuart == 1) {
		UBRR0L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
		UBRR0H = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
		UCSR0A = 0x00;
		UCSR0C = 0x06;
		UCSR0B = _BV(TXEN0)|_BV(RXEN0);
	}
	if(bootuart == 2) {
		UBRR1L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
		UBRR1H = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
		UCSR1A = 0x00;
		UCSR1C = 0x06;
		UCSR1B = _BV(TXEN1)|_BV(RXEN1);
	}
#elif defined __AVR_ATmega163__
	UBRR = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
	UBRRHI = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
	UCSRA = 0x00;
	UCSRB = _BV(TXEN)|_BV(RXEN);	
#elif defined(__AVR_ATmega168__) || defined(__AVR_ATmega328P__)

#ifdef DOUBLE_SPEED
	UCSR0A = (1<<U2X0); //Double speed mode USART0
	UBRR0L = (uint8_t)(F_CPU/(BAUD_RATE*8L)-1);
	UBRR0H = (F_CPU/(BAUD_RATE*8L)-1) >> 8;
#else
	UBRR0L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
	UBRR0H = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
#endif

UCSR0B = (1<<RXEN0) | (1<<TXEN0);
	UCSR0C = (1<<UCSZ00) | (1<<UCSZ01);

/* Enable internal pull-up resistor on pin D0 (RX), in order
	to supress line noise that prevents the bootloader from
	timing out (DAM: 20070509) */
	DDRD &= ~_BV(PIND0);
	PORTD |= _BV(PIND0);
#elif defined __AVR_ATmega8__
	/* m8 */
	UBRRH = (((F_CPU/BAUD_RATE)/16)-1)>>8; 	// set baud rate
	UBRRL = (((F_CPU/BAUD_RATE)/16)-1);
	UCSRB = (1<<RXEN)|(1<<TXEN);  // enable Rx & Tx
	UCSRC = (1<<URSEL)|(1<<UCSZ1)|(1<<UCSZ0);  // config USART; 8N1
#else
	/* m16,m32,m169,m8515,m8535 */
	UBRRL = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
	UBRRH = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
	UCSRA = 0x00;
	UCSRC = 0x06;
	UCSRB = _BV(TXEN)|_BV(RXEN);
#endif

#if defined __AVR_ATmega1280__
	/* Enable internal pull-up resistor on pin D0 (RX), in order
	to supress line noise that prevents the bootloader from
	timing out (DAM: 20070509) */
	/* feature added to the Arduino Mega --DC: 080930 */
	DDRE &= ~_BV(PINE0);
	PORTE |= _BV(PINE0);
#endif

/* set LED pin as output */
	LED_DDR |= _BV(LED);

/* flash onboard LED to signal entering of bootloader */
#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
	// 4x for UART0, 5x for UART1
	flash_led(NUM_LED_FLASHES + bootuart);
#else
	flash_led(NUM_LED_FLASHES);
#endif

/* 20050803: by DojoCorp, this is one of the parts provoking the
		 system to stop listening, cancelled from the original */
	//putch('\0');

/* forever loop */
	for (;;) {

/* get character from UART */
	ch = getch();

/* A bunch of if...else if... gives smaller code than switch...case ! */

/* Hello is anyone home ? */ 
	if(ch=='0') {
		nothing_response();
	}

/* Request programmer ID */
	/* Not using PROGMEM string due to boot block in m128 being beyond 64kB boundry  */
	/* Would need to selectively manipulate RAMPZ, and it's only 9 characters anyway so who cares.  */
	else if(ch=='1') {
		if (getch() == ' ') {
			putch(0x14);
			putch('A');
			putch('V');
			putch('R');
			putch(' ');
			putch('I');
			putch('S');
			putch('P');
			putch(0x10);
		} else {
			if (++error_count == MAX_ERROR_COUNT)
				app_start();
		}
	}

/* AVR ISP/STK500 board commands  DON'T CARE so default nothing_response */
	else if(ch=='@') {
		ch2 = getch();
		if (ch2>0x85) getch();
		nothing_response();
	}

/* AVR ISP/STK500 board requests */
	else if(ch=='A') {
		ch2 = getch();
		if(ch2==0x80) byte_response(HW_VER);		// Hardware version
		else if(ch2==0x81) byte_response(SW_MAJOR);	// Software major version
		else if(ch2==0x82) byte_response(SW_MINOR);	// Software minor version
		else if(ch2==0x98) byte_response(0x03);		// Unknown but seems to be required by avr studio 3.56
		else byte_response(0x00);				// Covers various unnecessary responses we don't care about
	}

/* Device Parameters  DON'T CARE, DEVICE IS FIXED  */
	else if(ch=='B') {
		getNch(20);
		nothing_response();
	}

/* Parallel programming stuff  DON'T CARE  */
	else if(ch=='E') {
		getNch(5);
		nothing_response();
	}

/* P: Enter programming mode  */
	/* R: Erase device, don't care as we will erase one page at a time anyway.  */
	else if(ch=='P' || ch=='R') {
		nothing_response();
	}

/* Leave programming mode  */
	else if(ch=='Q') {
		nothing_response();
#ifdef WATCHDOG_MODS
		// autoreset via watchdog (sneaky!)
		WDTCSR = _BV(WDE);
		while (1); // 16 ms
#endif
	}

/* Set address, little endian. EEPROM in bytes, FLASH in words  */
	/* Perhaps extra address bytes may be added in future to support > 128kB FLASH.  */
	/* This might explain why little endian was used here, big endian used everywhere else.  */
	else if(ch=='U') {
		address.byte[0] = getch();
		address.byte[1] = getch();
		nothing_response();
	}

/* Universal SPI programming command, disabled.  Would be used for fuses and lock bits.  */
	else if(ch=='V') {
		if (getch() == 0x30) {
			getch();
			ch = getch();
			getch();
			if (ch == 0) {
				byte_response(SIG1);
			} else if (ch == 1) {
				byte_response(SIG2); 
			} else {
				byte_response(SIG3);
			} 
		} else {
			getNch(3);
			byte_response(0x00);
		}
	}

/* Write memory, length is big endian and is in bytes  */
	else if(ch=='d') {
		length.byte[1] = getch();
		length.byte[0] = getch();
		flags.eeprom = 0;
		if (getch() == 'E') flags.eeprom = 1;
		for (w=0;w<length.word;w++) {
			buff[w] = getch();	                        // Store data in buffer, can't keep up with serial data stream whilst programming pages
		}
		if (getch() == ' ') {
			if (flags.eeprom) {		                //Write to EEPROM one byte at a time
				address.word <<= 1;
				for(w=0;w<length.word;w++) {
#if defined(__AVR_ATmega168__)  || defined(__AVR_ATmega328P__)
					while(EECR & (1<<EEPE));
					EEAR = (uint16_t)(void *)address.word;
					EEDR = buff[w];
					EECR |= (1<<EEMPE);
					EECR |= (1<<EEPE);
#else
					eeprom_write_byte((void *)address.word,buff[w]);
#endif
					address.word++;
				}			
			}
			else {					        //Write to FLASH one page at a time
				if (address.byte[1]>127) address_high = 0x01;	//Only possible with m128, m256 will need 3rd address byte. FIXME
				else address_high = 0x00;
#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__) || defined(__AVR_ATmega1281__)
				RAMPZ = address_high;
#endif
				address.word = address.word << 1;	        //address * 2 -> byte location
				/* if ((length.byte[0] & 0x01) == 0x01) length.word++;	//Even up an odd number of bytes */
				if ((length.byte[0] & 0x01)) length.word++;	//Even up an odd number of bytes
				cli();					//Disable interrupts, just to be sure
#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega1281__)
				while(bit_is_set(EECR,EEPE));			//Wait for previous EEPROM writes to complete
#else
				while(bit_is_set(EECR,EEWE));			//Wait for previous EEPROM writes to complete
#endif
				asm volatile(
					 "clr	r17		\n\t"	//page_word_count
					 "lds	r30,address	\n\t"	//Address of FLASH location (in bytes)
					 "lds	r31,address+1	\n\t"
					 "ldi	r28,lo8(buff)	\n\t"	//Start of buffer array in RAM
					 "ldi	r29,hi8(buff)	\n\t"
					 "lds	r24,length	\n\t"	//Length of data to be written (in bytes)
					 "lds	r25,length+1	\n\t"
					 "length_loop:		\n\t"	//Main loop, repeat for number of words in block							 							 
					 "cpi	r17,0x00	\n\t"	//If page_word_count=0 then erase page
					 "brne	no_page_erase	\n\t"						 
					 "wait_spm1:		\n\t"
					 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
					 "andi	r16,1           \n\t"
					 "cpi	r16,1           \n\t"
					 "breq	wait_spm1       \n\t"
					 "ldi	r16,0x03	\n\t"	//Erase page pointed to by Z
					 "sts	%0,r16		\n\t"
					 "spm			\n\t"							 
#ifdef __AVR_ATmega163__
					 ".word 0xFFFF		\n\t"
					 "nop			\n\t"
#endif
					 "wait_spm2:		\n\t"
					 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
					 "andi	r16,1           \n\t"
					 "cpi	r16,1           \n\t"
					 "breq	wait_spm2       \n\t"

"ldi	r16,0x11	\n\t"	//Re-enable RWW section
					 "sts	%0,r16		\n\t"						 			 
					 "spm			\n\t"
#ifdef __AVR_ATmega163__
					 ".word 0xFFFF		\n\t"
					 "nop			\n\t"
#endif
					 "no_page_erase:		\n\t"							 
					 "ld	r0,Y+		\n\t"	//Write 2 bytes into page buffer
					 "ld	r1,Y+		\n\t"							 
								 
					 "wait_spm3:		\n\t"
					 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
					 "andi	r16,1           \n\t"
					 "cpi	r16,1           \n\t"
					 "breq	wait_spm3       \n\t"
					 "ldi	r16,0x01	\n\t"	//Load r0,r1 into FLASH page buffer
					 "sts	%0,r16		\n\t"
					 "spm			\n\t"
								 
					 "inc	r17		\n\t"	//page_word_count++
					 "cpi r17,%1	        \n\t"
					 "brlo	same_page	\n\t"	//Still same page in FLASH
					 "write_page:		\n\t"
					 "clr	r17		\n\t"	//New page, write current one first
					 "wait_spm4:		\n\t"
					 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
					 "andi	r16,1           \n\t"
					 "cpi	r16,1           \n\t"
					 "breq	wait_spm4       \n\t"
#ifdef __AVR_ATmega163__
					 "andi	r30,0x80	\n\t"	// m163 requires Z6:Z1 to be zero during page write
#endif							 							 
					 "ldi	r16,0x05	\n\t"	//Write page pointed to by Z
					 "sts	%0,r16		\n\t"
					 "spm			\n\t"
#ifdef __AVR_ATmega163__
					 ".word 0xFFFF		\n\t"
					 "nop			\n\t"
					 "ori	r30,0x7E	\n\t"	// recover Z6:Z1 state after page write (had to be zero during write)
#endif
					 "wait_spm5:		\n\t"
					 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
					 "andi	r16,1           \n\t"
					 "cpi	r16,1           \n\t"
					 "breq	wait_spm5       \n\t"									 
					 "ldi	r16,0x11	\n\t"	//Re-enable RWW section
					 "sts	%0,r16		\n\t"						 			 
					 "spm			\n\t"					 		 
#ifdef __AVR_ATmega163__
					 ".word 0xFFFF		\n\t"
					 "nop			\n\t"
#endif
					 "same_page:		\n\t"							 
					 "adiw	r30,2		\n\t"	//Next word in FLASH
					 "sbiw	r24,2		\n\t"	//length-2
					 "breq	final_write	\n\t"	//Finished
					 "rjmp	length_loop	\n\t"
					 "final_write:		\n\t"
					 "cpi	r17,0		\n\t"
					 "breq	block_done	\n\t"
					 "adiw	r24,2		\n\t"	//length+2, fool above check on length after short page write
					 "rjmp	write_page	\n\t"
					 "block_done:		\n\t"
					 "clr	__zero_reg__	\n\t"	//restore zero register
#if defined __AVR_ATmega168__  || __AVR_ATmega328P__ || __AVR_ATmega128__ || __AVR_ATmega1280__ || __AVR_ATmega1281__ 
					 : "=m" (SPMCSR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31"
#else
					 : "=m" (SPMCR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31"
#endif
					 );
				/* Should really add a wait for RWW section to be enabled, don't actually need it since we never */
				/* exit the bootloader without a power cycle anyhow */
			}
			putch(0x14);
			putch(0x10);
		} else {
			if (++error_count == MAX_ERROR_COUNT)
				app_start();
		}		
	}

/* Read memory block mode, length is big endian.  */
	else if(ch=='t') {
		length.byte[1] = getch();
		length.byte[0] = getch();
#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
		if (address.word>0x7FFF) flags.rampz = 1;		// No go with m256, FIXME
		else flags.rampz = 0;
#endif
		address.word = address.word << 1;	        // address * 2 -> byte location
		if (getch() == 'E') flags.eeprom = 1;
		else flags.eeprom = 0;
		if (getch() == ' ') {		                // Command terminator
			putch(0x14);
			for (w=0;w < length.word;w++) {		        // Can handle odd and even lengths okay
				if (flags.eeprom) {	                        // Byte access EEPROM read
#if defined(__AVR_ATmega168__)  || defined(__AVR_ATmega328P__)
					while(EECR & (1<<EEPE));
					EEAR = (uint16_t)(void *)address.word;
					EECR |= (1<<EERE);
					putch(EEDR);
#else
					putch(eeprom_read_byte((void *)address.word));
#endif
					address.word++;
				}
				else {

if (!flags.rampz) putch(pgm_read_byte_near(address.word));
#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
					else putch(pgm_read_byte_far(address.word + 0x10000));
					// Hmmmm, yuck  FIXME when m256 arrvies
#endif
					address.word++;
				}
			}
			putch(0x10);
		}
	}

/* Get device signature bytes  */
	else if(ch=='u') {
		if (getch() == ' ') {
			putch(0x14);
			putch(SIG1);
			putch(SIG2);
			putch(SIG3);
			putch(0x10);
		} else {
			if (++error_count == MAX_ERROR_COUNT)
				app_start();
		}
	}

/* Read oscillator calibration byte */
	else if(ch=='v') {
		byte_response(0x00);
	}

#if defined MONITOR

/* here come the extended monitor commands by Erik Lins */

/* check for three times exclamation mark pressed */
	else if(ch=='!') {
		ch = getch();
		if(ch=='!') {
		ch = getch();
		if(ch=='!') {
			PGM_P welcome = "";
#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
			uint16_t extaddr;
#endif
			uint8_t addrl, addrh;

#ifdef CRUMB128
			welcome = "ATmegaBOOT / Crumb128 - (C) J.P.Kyle, E.Lins - 050815\n\r";
#elif defined PROBOMEGA128
			welcome = "ATmegaBOOT / PROBOmega128 - (C) J.P.Kyle, E.Lins - 050815\n\r";
#elif defined SAVVY128
			welcome = "ATmegaBOOT / Savvy128 - (C) J.P.Kyle, E.Lins - 050815\n\r";
#elif defined __AVR_ATmega1280__ 
			welcome = "ATmegaBOOT / Arduino Mega - (C) Arduino LLC - 090930\n\r";
#endif

/* turn on LED */
			LED_DDR |= _BV(LED);
			LED_PORT &= ~_BV(LED);

/* print a welcome message and command overview */
			for(i=0; welcome[i] != '\0'; ++i) {
				putch(welcome[i]);
			}

/* test for valid commands */
			for(;;) {
				putch('\n');
				putch('\r');
				putch(':');
				putch(' ');

ch = getch();
				putch(ch);

/* toggle LED */
				if(ch == 't') {
					if(bit_is_set(LED_PIN,LED)) {
						LED_PORT &= ~_BV(LED);
						putch('1');
					} else {
						LED_PORT |= _BV(LED);
						putch('0');
					}
				}

/* read byte from address */
				else if(ch == 'r') {
					ch = getch(); putch(ch);
					addrh = gethex();
					addrl = gethex();
					putch('=');
					ch = *(uint8_t *)((addrh << 8) + addrl);
					puthex(ch);
				}

/* write a byte to address  */
				else if(ch == 'w') {
					ch = getch(); putch(ch);
					addrh = gethex();
					addrl = gethex();
					ch = getch(); putch(ch);
					ch = gethex();
					*(uint8_t *)((addrh << 8) + addrl) = ch;
				}

/* read from uart and echo back */
				else if(ch == 'u') {
					for(;;) {
						putch(getch());
					}
				}
#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
				/* external bus loop  */
				else if(ch == 'b') {
					putch('b');
					putch('u');
					putch('s');
					MCUCR = 0x80;
					XMCRA = 0;
					XMCRB = 0;
					extaddr = 0x1100;
					for(;;) {
						ch = *(volatile uint8_t *)extaddr;
						if(++extaddr == 0) {
							extaddr = 0x1100;
						}
					}
				}
#endif

else if(ch == 'j') {
					app_start();
				}

} /* end of monitor functions */

}
		}
	}
	/* end of monitor */
#endif
	else if (++error_count == MAX_ERROR_COUNT) {
		app_start();
	}
	} /* end of forever loop */

}

char gethexnib(void) {
	char a;
	a = getch(); putch(a);
	if(a >= 'a') {
		return (a - 'a' + 0x0a);
	} else if(a >= '0') {
		return(a - '0');
	}
	return a;
}

char gethex(void) {
	return (gethexnib() << 4) + gethexnib();
}

void puthex(char ch) {
	char ah;

ah = ch >> 4;
	if(ah >= 0x0a) {
		ah = ah - 0x0a + 'a';
	} else {
		ah += '0';
	}
	
	ch &= 0x0f;
	if(ch >= 0x0a) {
		ch = ch - 0x0a + 'a';
	} else {
		ch += '0';
	}
	
	putch(ah);
	putch(ch);
}

void putch(char ch)
{
#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
	if(bootuart == 1) {
		while (!(UCSR0A & _BV(UDRE0)));
		UDR0 = ch;
	}
	else if (bootuart == 2) {
		while (!(UCSR1A & _BV(UDRE1)));
		UDR1 = ch;
	}
#elif defined(__AVR_ATmega168__)  || defined(__AVR_ATmega328P__)
	while (!(UCSR0A & _BV(UDRE0)));
	UDR0 = ch;
#else
	/* m8,16,32,169,8515,8535,163 */
	while (!(UCSRA & _BV(UDRE)));
	UDR = ch;
#endif
}

char getch(void)
{
#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
	uint32_t count = 0;
	if(bootuart == 1) {
		while(!(UCSR0A & _BV(RXC0))) {
			/* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/               
			/* HACKME:: here is a good place to count times*/
			count++;
			if (count > MAX_TIME_COUNT)
				app_start();
			}

return UDR0;
		}
	else if(bootuart == 2) {
		while(!(UCSR1A & _BV(RXC1))) {
			/* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/               
			/* HACKME:: here is a good place to count times*/
			count++;
			if (count > MAX_TIME_COUNT)
				app_start();
		}

return UDR1;
	}
	return 0;
#elif defined(__AVR_ATmega168__)  || defined(__AVR_ATmega328P__)
	uint32_t count = 0;
	while(!(UCSR0A & _BV(RXC0))){
		/* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/               
		/* HACKME:: here is a good place to count times*/
		count++;
		if (count > MAX_TIME_COUNT)
			app_start();
	}
	return UDR0;
#else
	/* m8,16,32,169,8515,8535,163 */
	uint32_t count = 0;
	while(!(UCSRA & _BV(RXC))){
		/* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/               
		/* HACKME:: here is a good place to count times*/
		count++;
		if (count > MAX_TIME_COUNT)
			app_start();
	}
	return UDR;
#endif
}

void getNch(uint8_t count)
{
	while(count--) {
#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
		if(bootuart == 1) {
			while(!(UCSR0A & _BV(RXC0)));
			UDR0;
		} 
		else if(bootuart == 2) {
			while(!(UCSR1A & _BV(RXC1)));
			UDR1;
		}
#elif defined(__AVR_ATmega168__)  || defined(__AVR_ATmega328P__)
		getch();
#else
		/* m8,16,32,169,8515,8535,163 */
		/* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/               
		//while(!(UCSRA & _BV(RXC)));
		//UDR;
		getch(); // need to handle time out
#endif		
	}
}

void byte_response(uint8_t val)
{
	if (getch() == ' ') {
		putch(0x14);
		putch(val);
		putch(0x10);
	} else {
		if (++error_count == MAX_ERROR_COUNT)
			app_start();
	}
}

void nothing_response(void)
{
	if (getch() == ' ') {
		putch(0x14);
		putch(0x10);
	} else {
		if (++error_count == MAX_ERROR_COUNT)
			app_start();
	}
}

void flash_led(uint8_t count)
{
	while (count--) {
		LED_PORT |= _BV(LED);
		_delay_ms(100);
		LED_PORT &= ~_BV(LED);
		_delay_ms(100);
	}
}

/* end of file ATmegaBOOT.c */

変更されたテキスト

ファイルを開く

/**********************************************************/
/* Serial Bootloader for Atmel megaAVR Controllers        */
/*                                                        */
/* tested with ATmega8, ATmega128 and ATmega168           */
/* should work with other mega's, see code for details    */
/*                                                        */
/* ATmegaBOOT.c                                           */
/*                                                        */
/* 20130613: Added support for ATmega128RFA1              */
/* 20090308: integrated Mega changes into main bootloader */
/*           source by D. Mellis                          */
/* 20080930: hacked for Arduino Mega (with the 1280       */
/*           processor, backwards compatible)             */
/*           by D. Cuartielles                            */
/* 20070626: hacked for Arduino Diecimila (which auto-    */
/*           resets when a USB connection is made to it)  */
/*           by D. Mellis                                 */
/* 20060802: hacked for Arduino by D. Cuartielles         */
/*           based on a previous hack by D. Mellis        */
/*           and D. Cuartielles                           */
/*                                                        */
/* Monitor and debug functions were added to the original */
/* code by Dr. Erik Lins, chip45.com. (See below)         */
/*                                                        */
/* Thanks to Karl Pitrich for fixing a bootloader pin     */
/* problem and more informative LED blinking!             */
/*                                                        */
/* For the latest version see:                            */
/* http://www.chip45.com/                                 */
/*                                                        */
/* ------------------------------------------------------ */
/*                                                        */
/* based on stk500boot.c                                  */
/* Copyright (c) 2003, Jason P. Kyle                      */
/* All rights reserved.                                   */
/* see avr1.org for original file and information         */
/*                                                        */
/* This program is free software; you can redistribute it */
/* and/or modify it under the terms of the GNU General    */
/* Public License as published by the Free Software       */
/* Foundation; either version 2 of the License, or        */
/* (at your option) any later version.                    */
/*                                                        */
/* This program is distributed in the hope that it will   */
/* be useful, but WITHOUT ANY WARRANTY; without even the  */
/* implied warranty of MERCHANTABILITY or FITNESS FOR A   */
/* PARTICULAR PURPOSE.  See the GNU General Public        */
/* License for more details.                              */
/*                                                        */
/* You should have received a copy of the GNU General     */
/* Public License along with this program; if not, write  */
/* to the Free Software Foundation, Inc.,                 */
/* 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA */
/*                                                        */
/* Licence can be viewed at                               */
/* http://www.fsf.org/licenses/gpl.txt                    */
/*                                                        */
/* Target = Atmel AVR m128,m64,m32,m16,m8,m162,m163,m169, */
/* m8515,m8535. ATmega161 has a very small boot block so  */
/* isn't supported.                                       */
/*                                                        */
/* Tested with m168                                       */
/**********************************************************/

/* $Id$ */

/* some includes */
#include <inttypes.h>
#include <avr/io.h>
#include <avr/pgmspace.h>
#include <avr/interrupt.h>
#include <avr/wdt.h>
#include <util/delay.h>

/* Use the F_CPU defined in Makefile */

/* 20070707: hacked by David A. Mellis - after this many errors give up and launch application */
#define MAX_ERROR_COUNT 5

/* set the UART baud rate */
/* 20060803: hacked by DojoCorp */
//#define BAUD_RATE   115200
#ifndef BAUD_RATE
#define BAUD_RATE   19200
#endif

/* Adjust to suit whatever pin your hardware uses to enter the bootloader */
/* ATmega128 has two UARTS so two pins are used to enter bootloader and select UART */
/* ATmega1280 has four UARTS, but for Arduino Mega, we will only use RXD0 to get code */
/* BL0... means UART0, BL1... means UART1 */
#ifdef __AVR_ATmega128__
#define BL_DDR  DDRF
#define BL_PORT PORTF
#define BL_PIN  PINF
#define BL0     PINF7
#define BL1     PINF6
/*#elif defined __AVR_ATmega128RFA1__*/
/* ToDO Enable bootloading via both UARTs */
#elif defined __AVR_ATmega1280__ 
/* we just don't do anything for the MEGA and enter bootloader on reset anyway*/
#else
/* other ATmegas have only one UART, so only one pin is defined to enter bootloader */
#define BL_DDR  DDRD
#define BL_PORT PORTD
#define BL_PIN  PIND
#define BL      PIND6
#endif

/* onboard LED is used to indicate, that the bootloader was entered (3x flashing) */
/* if monitor functions are included, LED goes on after monitor was entered */
#if defined __AVR_ATmega128__ || defined __AVR_ATmega1280__ || defined __AVR_ATmega128RFA1__
/* Onboard LED is connected to pin PB7 (e.g. Crumb128, PROBOmega128, Savvy128, Arduino Mega) */
#define LED_DDR  DDRB
#define LED_PORT PORTB
#define LED_PIN  PINB
#define LED      PINB7
#else
/* Onboard LED is connected to pin PB5 in Arduino NG, Diecimila, and Duomilanuove */ 
/* other boards like e.g. Crumb8, Crumb168 are using PB2 */
#define LED_DDR  DDRB
#define LED_PORT PORTB
#define LED_PIN  PINB
#define LED      PINB5
#endif

/* monitor functions will only be compiled when using ATmega128, due to bootblock size constraints */
#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
#define MONITOR 1
#endif

/* define various device id's */
/* manufacturer byte is always the same */
#define SIG1	0x1E	// Yep, Atmel is the only manufacturer of AVR micros.  Single source :(

#if defined __AVR_ATmega1280__
#define SIG2	0x97
#define SIG3	0x03
#define PAGE_SIZE	0x80U	//128 words

#elif defined __AVR_ATmega1281__
#define SIG2	0x97
#define SIG3	0x04
#define PAGE_SIZE	0x80U	//128 words

#elif defined __AVR_ATmega128__
#define SIG2	0x97
#define SIG3	0x02
#define PAGE_SIZE	0x80U	//128 words

#elif defined __AVR_ATmega128RFA1__
#define SIG2	0xA7
#define SIG3	0x01
#define PAGE_SIZE	0x80U	// 128 words