Untitled diff
建立於 差異永不過期
# For more options and information see
#Modifcations to /boot/* files, will not be saved when powered on.
# http://rpf.io/configtxtreadme
#Please ensure you edit from the DietPi-RamDisk location /DietPi/*
# Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
#hdmi_safe=1
# uncomment this if your display has a black border of unused pixels visible
# Set to 1 if your display has a black border of unused pixels visible
# and your display can output without overscan
disable_overscan=1
#disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_left=16
#overscan_right=16
#overscan_right=16
#overscan_top=16
#overscan_top=16
#overscan_bottom=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# uncomment to force a console size. By default it will be display's size minus
# overscan.
framebuffer_width=1280
#framebuffer_width=1280
framebuffer_height=720
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1
#hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_group=1
#hdmi_mode=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
# DMT (computer monitor) modes
#hdmi_drive=2
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
# no display
#config_hdmi_boost=4
#config_hdmi_boost=4
# uncomment for composite PAL
# uncomment for composite PAL
#sdtv_mode=2
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#-------RPi Camera Module-------
#arm_freq=800
start_x=0
disable_camera_led=0
# Uncomment some or all of these to enable the optional hardware interfaces
#-------GPU memory Splits-------
#dtparam=i2c_arm=on
gpu_mem_256=16
#dtparam=i2s=on
gpu_mem_512=16
#dtparam=spi=on
gpu_mem_1024=16
# Uncomment this to enable the lirc-rpi module
#-------Max USB Current -------
#dtoverlay=lirc-rpi
max_usb_current=1
# Additional overlays and parameters are documented /boot/overlays/README
#-------Disable Ram temp refresh every 500ms---------------
disable_pvt=1
# Enable audio (loads snd_bcm2835)
#-------Disable Pi Splash screen on boot-------------
dtparam=audio=on
disable_splash=1
#-------Remove dedicated pll for PWM audio -------
avoid_pwm_pll=1
#-------SoundCard-------
dtparam=audio=off
#-------i2c-------------
dtparam=i2c_arm=off
dtparam=i2c1=off
i2c_arm_baudrate=100000
#-------Overclock-------
temp_limit=65
initial_turbo=20
force_turbo=0
#over_voltage=0
#arm_freq=900
#core_freq=250
#sdram_freq=400
#arm_freq_min=700
#core_freq_min=250
#sdram_freq_min=400
#Note To Self, NEVER enable L2 cache, breaks most X based applications that were not compiled with L2 cache enabled.
decode_MPG2=0x46de3941
decode_MPG2=0x46de3941
decode_WVC1=0xf402b3ea
decode_WVC1=0xf402b3ea