टेक्स्ट की तुलना करें

दो टेक्स्ट फ़ाइलों के बीच अंतर ढूंढें

रियल-टाइम एडिटर
अपरिवर्तित संक्षिप्त करें
लाइन रैप बंद
लेआउट
परिवर्तन हाइलाइट करें
सिंटैक्स हाइलाइटिंग

Untitled diff

बनाया गया Diff कभी समाप्त नहीं होता
20 हटाए गए
60 लाइनें
43 जोड़े गए
86 लाइनें
# For more options and information see
#Modifcations to /boot/* files, will not be saved when powered on.
# http://rpf.io/configtxtreadme
#Please ensure you edit from the DietPi-RamDisk location /DietPi/*
# Some settings may impact device functionality. See link above for details


# uncomment if you get no picture on HDMI for a default "safe" mode
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
#hdmi_safe=1


# uncomment this if your display has a black border of unused pixels visible
# Set to 1 if your display has a black border of unused pixels visible
# and your display can output without overscan
disable_overscan=1
#disable_overscan=1


# uncomment the following to adjust overscan. Use positive numbers if console
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_left=16
#overscan_right=16
#overscan_right=16
#overscan_top=16
#overscan_top=16
#overscan_bottom=16
#overscan_bottom=16


# uncomment to force a console size. By default it will be display's size minus
# uncomment to force a console size. By default it will be display's size minus
# overscan.
framebuffer_width=1280
#framebuffer_width=1280
framebuffer_height=720
#framebuffer_height=720


# uncomment if hdmi display is not detected and composite is being output
# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1
#hdmi_force_hotplug=1


# uncomment to force a specific HDMI mode (this will force VGA)
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_group=1
#hdmi_mode=1
#hdmi_mode=1


# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
# DMT (computer monitor) modes
#hdmi_drive=2
#hdmi_drive=2


# uncomment to increase signal to HDMI, if you have interference, blanking, or
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
# no display
#config_hdmi_boost=4
#config_hdmi_boost=4


# uncomment for composite PAL
# uncomment for composite PAL
#sdtv_mode=2
#sdtv_mode=2


#uncomment to overclock the arm. 700 MHz is the default.
#-------RPi Camera Module-------
#arm_freq=800
start_x=0
disable_camera_led=0


# Uncomment some or all of these to enable the optional hardware interfaces
#-------GPU memory Splits-------
#dtparam=i2c_arm=on
gpu_mem_256=16
#dtparam=i2s=on
gpu_mem_512=16
#dtparam=spi=on
gpu_mem_1024=16


# Uncomment this to enable the lirc-rpi module
#-------Max USB Current -------
#dtoverlay=lirc-rpi
max_usb_current=1


# Additional overlays and parameters are documented /boot/overlays/README
#-------Disable Ram temp refresh every 500ms---------------
disable_pvt=1


# Enable audio (loads snd_bcm2835)
#-------Disable Pi Splash screen on boot-------------
dtparam=audio=on
disable_splash=1

#-------Remove dedicated pll for PWM audio -------
avoid_pwm_pll=1

#-------SoundCard-------
dtparam=audio=off

#-------i2c-------------
dtparam=i2c_arm=off
dtparam=i2c1=off
i2c_arm_baudrate=100000

#-------Overclock-------
temp_limit=65
initial_turbo=20
force_turbo=0

#over_voltage=0
#arm_freq=900
#core_freq=250
#sdram_freq=400

#arm_freq_min=700
#core_freq_min=250
#sdram_freq_min=400

#Note To Self, NEVER enable L2 cache, breaks most X based applications that were not compiled with L2 cache enabled.


decode_MPG2=0x46de3941
decode_MPG2=0x46de3941
decode_WVC1=0xf402b3ea
decode_WVC1=0xf402b3ea


सेव किए गए Diffs